possible to change oil pan gasket with motor in?

Jason 302

10 Year Member

Aug 9, 2003

685

71

68

Newark, Ohio

Jun 7, 2004

#1

• Jun 7, 2004

• #1

My oil pan gasket has stepped out a bit right under the dipstick and I was wondering if anybody has ever changed one with the motor still in the car? It looks like it would be really tough and I don't think it's possible but??????

 

ECU5.0

Banned

Jan 10, 2004

1,803

1

0

raleigh, nc

Jun 7, 2004

#2

• Jun 7, 2004

• #2

i think you can...not sure how...but ive heard of someone doin it on here

 

88stangmangt

Active Member

Nov 25, 2003

2,332

1

48

Stafford,VA

Jun 7, 2004

#3

• Jun 7, 2004

• #3

ya you can do it gonna be a bitch trust me.!!!!!

 

F

Fastcat

Founding Member

Mar 5, 2002

582

0

0

St. Louis

Jun 7, 2004

#4

• Jun 7, 2004

• #4

Its possible if you drop the k-member, or the tranny, other than that... good luck!

 

86Cobra

Founding Member

Jun 6, 2000

2,064

1

0

Phoenix, AZ

Jun 7, 2004

#5

• Jun 7, 2004

• #5

Yeah, I've done it a couple of times. I have a tubular k-member (helps), a 7 quart Moroso pan (doesn't help), and a scattershield (doesn't help). You should be able to do it with a stock pan and k-member. You'll have to pull the steering rack loose from the k-member and steering shaft.

If you need more room, disconnect the motor mounts from the k-member and jack up the motor. Use a block of wood on your jack so you don't damage anything. You can jack under the balancer or the bellhousing/tranny.

 

88stangmangt

Active Member

Nov 25, 2003

2,332

1

48

Stafford,VA

Jun 7, 2004

#6

• Jun 7, 2004

• #6

nah i beleive you can still drop it enough with the k-member still on if you got the motor jacked up and the fan/shroud gone.

 

408stroker5.0

The world would be a better place if all males jus

Mar 10, 2004

639

0

16

Bonnyville, Alberta, CANADA

Jun 7, 2004

#7

• Jun 7, 2004

• #7

NIGHTMARE......
If it was me I'd pull the engine and do it right.

 

donkey_punch

New Member

Jan 16, 2004

565

0

0

northern****ingjersey

Jun 7, 2004

#8

• Jun 7, 2004

• #8

it can be done, but like said above it's a bitch.
take your mid pipe off, and i think the drive shaft too. motor mounts and jack the motor up. and i hope your planning on useing a lift.

 

Stang8URMPRT

Active Member

Dec 28, 2003

1,100

1

38

Daytona Beach, FL

Jun 7, 2004

#9

• Jun 7, 2004

• #9

What the hell are you all talking about? I've done a bazillion of these. It's as easy and taking the bolts off the motor mounts in the k member and jacking the motor with a block or wood on the balancer. This will give you plenty of room. I have done an oil pump with the motor in the car. Now that was a bitch, but a pan gasket isn't what you all make it out to be.

Nick

 

T

trendkilllx

New Member

Aug 28, 2003

79

0

0

Las Vegas

Jun 8, 2004

#10

• Jun 8, 2004

• #10

It's possible to do it with out lifting the motor or droping the k. I did on mine and it was a pain. Took 3 hours but I got it. It would have been a ton easier if I just jacked up the motor. I unbolted the pan and it droped about an inch, that was enough room.

 

drgn5.0

Founding Member

Mar 13, 2001

603

0

0

Jun 8, 2004

#11

• Jun 8, 2004

• #11

who takes the driveshaft off?? and why? disconnect the headers/exhaust, remove rad/shroud, unbolt motor mounts and lift up.

 

Stang8URMPRT

Active Member

Dec 28, 2003

1,100

1

38

Daytona Beach, FL

Jun 8, 2004

#12

• Jun 8, 2004

• #12

You don't need to disconnect anything other then the motor mounts and fan shroud if needed. Jack up the motor until the bellhousing hits the firewall and that's as far as you can go. Not that hard.

 

88stangmangt

Active Member

Nov 25, 2003

2,332

1

48

Stafford,VA

Jun 8, 2004

#13

• Jun 8, 2004

• #13

Stang8URMPRT said:

You don't need to disconnect anything other then the motor mounts and fan shroud if needed. Jack up the motor until the bellhousing hits the firewall and that's as far as you can go. Not that hard.

Click to expand...

seriously...................................... why id everyone makeing it out to be so d@mn hard????????? he is prob already done it by now.

 

Stang8URMPRT

Active Member

Dec 28, 2003

1,100

1

38

Daytona Beach, FL

Jun 8, 2004

#14

• Jun 8, 2004

• #14

88stangmangt said:

seriously...................................... why id everyone makeing it out to be so d@mn hard????????? he is prob already done it by now.

Click to expand...

lmao.. I know. He's probably reading this like "Damn, didn't mean to start WW3 over an oil pan gasket" lol

Nick