• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

quench clearance

  • Thread starter Thread starter 352Ford2
  • Start date Start date Jul 31, 2006

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Jul 31, 2006
#1
  • Jul 31, 2006
  • #1
How tight of quench clearance do you think I can run with this combo?

SBF 302, cheap scat steel rods, and not planning on reving over 6 grand


Right now it is looking like the piston is out of the hole 0.014 and felpro claims my headgasket is compressed 0.039 so that works out to be 0.025.

A little tighter than I was planning on, what do you think, get a different headgasket?
 

eagleautosports

New Member
Jul 7, 2006
139
0
0
Mebane NC
Jul 31, 2006
#2
  • Jul 31, 2006
  • #2
I know Cometic makes gaskets for this problem. I think they could actually go as thick as .080.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jul 31, 2006
#3
  • Jul 31, 2006
  • #3
.025" is a little tight but with a steel rod you may be ok, ROL makes a .051" thick graphite style gasket that would get you closer to the norm .035"-.039"
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Jul 31, 2006
#4
  • Jul 31, 2006
  • #4
How tight have people run their quench clearance?

I really would like that as tight as possible (also I would rather not have to get different gaskets.) I would really like to be able to back off the timing and run cheap gas when I am not at the track (its going to have about 9.6:1 CR and iron heads) and running the tight clearance would help that, and make me some more power. Its set up for N2O so the piston to bore clearance is a touch looser (1.5 times speed pro spec) so there will be a touch more piston rock, which isn’t helping me on this issue.
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Jul 31, 2006
#5
  • Jul 31, 2006
  • #5
Update:
I rechecked everything (the measurement I took before were quick and dirty only on number 5 cyl with a straight edge and a feeler gauge). I did it right and used a piston stop and dial indicator.

#1: 0.007 out of the hole
#2: 0.007 out of the hole
#3: 0.006 out of the hole
#4: 0.007 out of the hole
#5: 0.008 out of the hole
#6: 0.007 out of the hole
#7: 0.003 out of the hole
#8: 0.003 out of the hole


so with my 0.039 gasket the quench clearances are 0.033, 0.034, 0.035, 0.038. which is still tight, but I think doable.

It kind of bothers me that two of those cylnders are 4 thou out of the hole less than the others.

ideas?
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Aug 1, 2006
#6
  • Aug 1, 2006
  • #6
ttt
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Aug 1, 2006
#7
  • Aug 1, 2006
  • #7
so only me,rick, and eagle are the only ones on stangnet that care about or check quench clearance?

thats disapointing...
 

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Aug 1, 2006
#8
  • Aug 1, 2006
  • #8
What was your method with the dial indicator? .004 is a tight difference, but still a tad concerning. I would double check...do you have the pan on it already?!
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Aug 2, 2006
#9
  • Aug 2, 2006
  • #9
I used the piston stop, set up and zeroed the dial indcator, removed the piston stop, spun the motor and recorded how high it went, I did it a couple times so I am pretty sure its +/- 1 thou

yeah the oil pan is still off
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Aug 2, 2006
#10
  • Aug 2, 2006
  • #10
The deck being crooked/uneven really doesn't surprise me much you see that with most of the stock stuff. I had a stock 74 351 that was .014" high up front bank 1, .014 high in the rear on bank 2...twisted.

.033" will be fine, I usually shoot for .038" We have run as tight as .018 on some race stuff but you need to have everything right or.....BOOM!

You could deck the pistons and block to make everything straight or atleast split the difference.
 
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
  • Locked
Engine Might have to get a Dart block but don't want to and if I do, then 363 instead of 331. Thoughts on what I've already bought so far.......
  • from6to8
  • Jul 8, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
641
Fox 5.0 Mustang Tech Jul 8, 2025
Noobz347
Progress Thread 351w Build, 67 Coupe
  • redstang67
  • Oct 4, 2024
  • Classic Mustang Specific Tech
Replies
3
Views
450
Classic Mustang Specific Tech Oct 5, 2024
89ripper
Might have to get a Dart block but don't want to and if I do, then 363 instead of 331. Thoughts on what I've already bought so far.......
  • from6to8
  • Jul 8, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
52
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 9, 2025
from6to8
Motor given to me and I’d like to rebuild it what do I need to do
  • Creomod
  • Dec 14, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
526
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 16, 2024
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?