• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Rear end whining/Alignment issue

  • Thread starter Thread starter 94GTPilot
  • Start date Start date Apr 29, 2006
9

94GTPilot

Member
Mar 26, 2006
82
0
6
Apr 29, 2006
#1
  • Apr 29, 2006
  • #1
Well the combination of these two have really started to get on my nerves the past few months.. For starters, my car is soo squirrely on the road it's starting to scare me.

When I looked at it more closely after jacking up the front end, I can grab the tire, and slightly wiggle it side to side, but not up and down. Somebody told me it could be the tie rod ends? Sound right to you?

Also, I have a whine coming from the rear, possibly the rear end? But the weird part is I only notice it when I accelerate. A second or two after I let off the gas, the whine goes away.. The car has a lot of miles on it, so I'm guessing something is running low on life.... Any help would be greatly appreciated.. Thanks!! :SNSign:
 

Swarzkopf

Member
Sep 23, 2004
973
0
16
Pittsburgh
Apr 29, 2006
#2
  • Apr 29, 2006
  • #2
Well the combination of these two have really started to get on my nerves the past few months.. For starters, my car is soo squirrely on the road it's starting to scare me.
Click to expand...

What do you mean by "squirrely"? It wanders? Won't go in the direction you point it?

When I looked at it more closely after jacking up the front end, I can grab the tire, and slightly wiggle it side to side, but not up and down. Somebody told me it could be the tie rod ends? Sound right to you?
Click to expand...

Both sides?

Yep, it definitely could be your tie rod ends. It also could be your ball joints. Both can and will go bad, and both will cause failure of the tire wiggle test.

Check the condition of the rubber dust boot covering the ball-joints...if it's ripped or torn, there's a real good chance the ball joint is bad. If it's not, check for a puncture near the top- this is how the ball joint grease is applied, through a puncture hole. If one exists, try to force some grease out of it. If the grease that comes out is dirty and gritty, there's a real good chance the ball joint is bad.

If the ball joints check out, replace the tie rod ends.

Also, I have a whine coming from the rear, possibly the rear end? But the weird part is I only notice it when I accelerate. A second or two after I let off the gas, the whine goes away..
Click to expand...

Change the differential fluid. Inspect the rear end while the cover is off. If you find any broken teeth, chunks of metal, ect. report back to us.
 

Swarzkopf

Member
Sep 23, 2004
973
0
16
Pittsburgh
Apr 29, 2006
#3
  • Apr 29, 2006
  • #3
Oh...and this should have gone in Tech.
 
9

94GTPilot

Member
Mar 26, 2006
82
0
6
Apr 29, 2006
#4
  • Apr 29, 2006
  • #4
Sorry about the location... Still trying to navigate my way through all this info! lol..

About the "squirreliness".. I mean when Im driving, the front end will kinda pull to one direction or another without any input from me, which requires me to steer the other way. Makes for a very difficult, annoying drive to/from work..

I will have to check on the rear end next weekend. I have a friend that works for a dealership, so we have access to a lift/tools... I bought a King Cobra clutch, steel bearing retainer, adjustable clutch cable, new fork, pivot bearing, and pilot bearing, so while its up in the air, we will check the rear end and get back to you. Thanks for the help!!
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Apr 29, 2006
#5
  • Apr 29, 2006
  • #5
you better install some new tie rod ends and check balljoints as Swarzkopf recommended replace if necessary and get a front end alignment before you wander into a ditch. the rear end is not so much as serious issue at this point...alot of people have gear whine and drive like that for thousands of miles with no problems...i would not recommend driving this vehicle in this condition...
 

94-302-vert

Active Member
Aug 16, 2004
1,947
2
36
NE CT
May 1, 2006
#6
  • May 1, 2006
  • #6
Check your bushings on the front control arms too...
 
You must log in or register to reply here.

Similar threads

Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
428
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
221
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
What's your tow rig?
  • LILCBRA
  • May 31, 2026
  • Other Auto Tech
Replies
3
Views
144
Other Auto Tech May 31, 2026
LILCBRA
J
Hello all, I have returned from a hiatus... Update and Questions
  • JackH
  • Aug 13, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
6
Views
345
1974 - 1978 Mustang II Talk & Tech Aug 15, 2025
JackH
J
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
401
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?