• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Rearend Help

  • Thread starter Thread starter marine_2003
  • Start date Start date Oct 16, 2005

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 16, 2005
#1
  • Oct 16, 2005
  • #1
Can anyone tell me how to get the seals and bearings in my 8.8 out? I want to put new ones in and would rather not pay someone to do it.

Thanks
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 16, 2005
#2
  • Oct 16, 2005
  • #2
Which ones?

The outer axle bearings and seals should be easy, remove the cover, drain the oil, remove the cross pin retaining bolt, pull the cross pin, push the axles in, remove the c-clips, remove the axles, then pull the seals, and then the outer bearings.

The pinion seal is a bit more involved, you have to remove the pinion nut, pull the yoke, change the seal and reinstall. However, you must retorque the pinion nut in small stages, to get the same preload. Best to get a book for that one.

The carrier and pinion bearings require removal of the carrier. That can also be done, but reassembly of the pinion, crush sleeve, yoke and nut takes some heavy torque, in small stages, to sneek up on the right value. You should have a detailed manual, or a friend with experience for this one.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Oct 16, 2005
#3
  • Oct 16, 2005
  • #3
Those seals are good i need to replace the outer seals and bearings the ones in the axle tubes
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 17, 2005
#4
  • Oct 17, 2005
  • #4
The rear wheel bearings are the ones at the outer ends of the axle tubes. Just follow the steps in part one of my earlier post. It requires removing the rear cover and draining the fluid, pulling the crosspin and c-clips, etc. It can be messy, and can be a time consuming process, probably 4 hours to change both sides. Once you get the cross pin and c-clips out the rest is easy.

Just go carefully when you try to unscrew the cross pin retaining bolt, ie, make sure you use a six point socket, and such. If you round off that bolt head, the fix is a mother......

There have been two types of bearings used at the wheel bearing, one is a tight fit and one is a looser, push in fit. If the original is a press in, it will take an internal bearing puller of some sort to pull it, or some destruction to get it out.

I just did this job on my 89, and the bearings and axles looked fine, so I put new seals in and put it back together.

Also, make sure the fill plug can be removed before you put it all back together. Filling it up, from on the ground, under the car is slow. I use a small pump that fits in the oil bottle.
 
You must log in or register to reply here.

Similar threads

J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
337
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
704
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
Interior and Upholstery HVAC Mode selector vacuum switch issue.
  • parish99
  • Jul 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
182
Fox 5.0 Mustang Tech Aug 3, 2026
KAWMAN2
O
8.8 Pinion Nut Leak
  • OX1
  • Jan 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 5, 2026
OX1
O
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?