• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

rtech pinion settingtool doesnt seem to work

  • Thread starter Thread starter rockyracoon
  • Start date Start date Jun 14, 2006
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
Jun 14, 2006
#1
  • Jun 14, 2006
  • #1
ratech pinion settingtool doesnt seem to work

I purchased the tool from ratech and if I follow the instructions it makes no sense,this is what they tell you to do

"With the tool being held by your left hand firmly against the top of the pinion head and the slotted end touching the face of the axle tube, insert the dial caliper with your right hand into the slot and position the depth rod so it touches the bottom of the carrier bearing journal. (fig. 6)
Take the measurement from the dial caliper and subtract it from the dimension printed on the tool. The answer is the current checking distance of the pinion gear. Add the appropriate amount of shims to arrive at the number marked on the end of the pinion gear by the manufacturer".

I get 0.510 from the dial caliper if I subtract that from the number printed on the tool (3.152) I get 2.642,the number on the pinion head is 2.550,how am I to add the appropriate shims to arrive at that number that is scribed on the pinion,when it is a lower number than the checking distance?

0.510 meaurment from dial caliper
3.152 number printed on tool
2.550 number on pinion
I dont get it.
 
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
Jun 14, 2006
#2
  • Jun 14, 2006
  • #2
I spoke to tech support over at ratech and the problem Im having is most likely in regards to a little plastic insert that is in the center of the tool which is supposed to go into the hole on the pinion head, however in my case that little nib wouldnt fit in the hole in the pinion thus not letting the tool sit flush on the pinion head and that changed the geometry in terms of the dial calipers results.They told me that is why they make that little nib out of plastic so it can be filed if necessary.Hopefully this will allow me to accurately achieve the correct pinion shim.
 
You must log in or register to reply here.

Similar threads

3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
801
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
SN Mustang Magnum T56 swap
  • revhead347
  • May 24, 2024
  • 1994 - 1995 Specific Tech
Replies
15
Views
7K
1994 - 1995 Specific Tech Jun 28, 2026
GearHeadGuy
D
Brakes Low Brake Pedal After Service - Need Advice
  • Dennis M Wilson
  • Apr 6, 2017
  • SN95 4.6L Mustang Tech
Replies
4
Views
6K
SN95 4.6L Mustang Tech Apr 8, 2017
Sluggie24
S
I Have Had Enough With Ford!
  • GTA_V6_Mustang
  • Oct 15, 2014
  • 2005 - 2014 S-197 Mustang -General/Talk-
  • 2
Replies
30
Views
6K
2005 - 2014 S-197 Mustang -General/Talk- Apr 10, 2015
BlackenedSVT
J
My rear gear install experience
  • jtl
  • Apr 10, 2011
  • Fox 5.0 Mustang Tech
Replies
1
Views
937
Fox 5.0 Mustang Tech Apr 10, 2011
03ghoststang
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?