• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-

Shooting for 12.40s, what do you think it will run?

  • Thread starter Thread starter mrmustangman357
  • Start date Start date Apr 24, 2009

mrmustangman357

Member
Feb 11, 2007
763
3
18
Apr 24, 2009
#1
  • Apr 24, 2009
  • #1
Shooting for 12s, what do you think it will run?

Haven't been to the track in a lllllloooonnnnggggg time. Last time on my old setup:


The car is a 66 coupe 3000 lb with driver. Here is the combo:

Engine:
-357W 9.8:1 compression
-170cc Trick Flow Twisted Wedge Heads
-.530 lift 230 duration @.050 hydraulic roller cam 112 LSA I believe
-Edelbrock Performer RPM Air Gap intake with 750 holley vac sec. carb

This was the old run with a mild C4 and the stock 8" 2.79 axle. I couldn't get on it until about 60-80 ft out.

It ran 13.4 at 109 mph. New setup is a T5 with centerforce clutch and an 8.8 with 3.73s and posi, and nitto drag radials too. Make your guesses on et/MPH, and when it gets to the track we will see who's closest! Also any ideas on driving style launching a manual transmission car? I could use a few!
 

zookeeper

Founding Member
Aug 25, 2001
3,415
63
109
Rogue River, Oregon
Apr 25, 2009
#2
  • Apr 25, 2009
  • #2
Off hand I'd say 13-flat. The gears will help, but the manual trans may actually cost you a couple tenths. T5's are tough to speed shift in my experience, and I always had to back out of the throttle at least halfway on each shift. As for launch technique, I'd hold the RPM's at about 3000 and let the clutch out smoothly but quickly. If it bogs go up a touch on the revs. I wouldn't just side-step the clutch, since that's a good way to break stuff and/or spin the tires.
 

blown65

Founding Member
Jul 7, 1999
1,938
4
39
Queen Creek Arizona
Apr 25, 2009
#3
  • Apr 25, 2009
  • #3
Ya, I'd say 12.9-13.2. If you got traction and shift good the 12.4's would be no problem however.
 

02 281 GT

Agreed...My wife has great Boobs
15 Year Member
Feb 3, 2009
3,208
1,972
194
Cabot, AR
Apr 25, 2009
#4
  • Apr 25, 2009
  • #4
zookeeper said:
Off hand I'd say 13-flat. The gears will help, but the manual trans may actually cost you a couple tenths. T5's are tough to speed shift in my experience, and I always had to back out of the throttle at least halfway on each shift. As for launch technique, I'd hold the RPM's at about 3000 and let the clutch out smoothly but quickly. If it bogs go up a touch on the revs. I wouldn't just side-step the clutch, since that's a good way to break stuff and/or spin the tires.
Click to expand...
They're not THAT tough to shift as long as you have a good aftermarket shifter with built-in stop bolts. Of course, if you power shift a T-5 you're GOING to break it. Not the first time, perhaps, but it's inevitable if you keep it up.

That being said, I think 12s are very easily attainable. You're going from 2.79s to 3.73s, and the smaller amount of parasitic loss with the manual versus the auto will help you out as well. And since you say "drag radials too" I assume that your previous time of 13.4 was on street tires. I agree with blown65 that if you shift good and get good traction you could get it down to a 12.4. Good luck!
 

mrmustangman357

Member
Feb 11, 2007
763
3
18
Apr 25, 2009
#5
  • Apr 25, 2009
  • #5
right, it ran the number before on 205 series rubber.

I talked with my insurance company and got tow coverage added, so that automatically raises my launch rpm by 2000 rpm. the old 60 ft time for the 13.4 run was ~2.45 IIRC
 
You must log in or register to reply here.

Similar threads

9
what do you guys think ill run?
  • 96darkhorse
  • Feb 19, 2009
  • 1994 - 1995 Specific Tech
Replies
6
Views
878
1994 - 1995 Specific Tech Feb 21, 2009
Venom351R
Just got my cam, what do you guys think of the specs?
  • Aliate X
  • Jul 9, 2007
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
37
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 12, 2007
superirish
S
what do you think of this camshaft???
  • MI95Cobra
  • Jan 8, 2007
  • 1994 - 1995 Specific Tech
Replies
2
Views
880
1994 - 1995 Specific Tech Jan 8, 2007
blksn955.o
P
Please HELP! Which cam do you reccomend?
  • PaLiAcH
  • May 15, 2007
  • SN95 4.6L Mustang Tech
Replies
2
Views
812
SN95 4.6L Mustang Tech May 15, 2007
steveb24
P
what do you think i'd get/run out of this setup?
  • plainwrecknate
  • Sep 11, 2005
  • Fox 5.0 Mustang Tech
Replies
10
Views
774
Fox 5.0 Mustang Tech Sep 12, 2005
my$100project
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?