• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Starter on 89 fox

  • Thread starter Thread starter TokyoJoe
  • Start date Start date Aug 3, 2007
T

TokyoJoe

New Member
Mar 25, 2007
179
5
0
Aug 3, 2007
#1
  • Aug 3, 2007
  • #1
Alright well I had the car shipped from Texas to Florida. When they started the car (I wasn't there) the starter was running non stop as soon as the ignition turned. The only way to get the starter to stop running was to disconnect the battery, which also made the car die. So they decided to drive the car onto the truck with the starter engaged during this time. When the truck reached my house in Florida the trucker connected the battery to start the car however after about two seconds the gear is gone and now the starter motor just spins freely and the car does not start.

My questions are

1. What could have caused this, a stuck solenoid?
2. Is the starter more than likely the only damaged part or am I looking at a new flywheel also?

TIA for the help guys I'm a little irritated right now
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 3, 2007
#2
  • Aug 3, 2007
  • #2
Solenoids often stick. The temporary fix is a sharp smack with a hammer on the bottom of the solenoid.

The other problem is the ignition switch. If it is bad, the solenoid will remain powered even when you let go of the key. Pull the small red/blue wire off the solenoid when it appears to be stuck. If the starter quits running, thr ignition switch is at fault.
 
T

TokyoJoe

New Member
Mar 25, 2007
179
5
0
Aug 3, 2007
#3
  • Aug 3, 2007
  • #3
Great thanks.

How about the flywheel, do you think it got knackered up?
 

corvetteguy

New Member
Jun 30, 2007
71
0
0
Aug 4, 2007
#4
  • Aug 4, 2007
  • #4


Start with the cheap stuff

Solenoid.
If necessary check the starter bendix

last the flywheel.
Can be checked when the starter is out.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Aug 4, 2007
#5
  • Aug 4, 2007
  • #5
If you still have a functional CSS or neutral safety switch, this should interupt the signal to the solenoid when the switch is open.



The bendix should have taken the brunt of the wear. You should be able to get a new ring gear pressed onto the flywheel if needed (as I recall the rings are a press-fit and not integral).

Good luck.
 
You must log in or register to reply here.

Similar threads

3
Electrical Starter solenoid out of space?
  • 387lx
  • Jan 22, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
527
Fox 5.0 Mustang Tech Jan 23, 2026
387lx
3
D
Mustang not starting
  • Dawry Ramos
  • Sep 12, 2026
  • 2015 - 2023 Specific Tech
Replies
10
Views
415
2015 - 2023 Specific Tech Oct 3, 2026
Dawry Ramos
D
M
85 mustang 5.0 cranking in run position
  • Mamaclean
  • May 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
264
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 1, 2026
General karthief
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
Alternator not charging
  • SchwarzStock
  • Jul 6, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
3
Views
269
1965 - 1973 Classic Mustangs -General/Talk- Oct 17, 2026
SchwarzStock
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?