starting problems

B

blue87lx

New Member

Apr 23, 2005

175

0

0

Jan 30, 2006

#1

• Jan 30, 2006

• #1

put a better running motor in my beater stang and now im having trouble starting it. the solinoid clicks but the starter wont engage. i tried swapping the noid and starter from my other stang and i get the same thing. could it be somthing with the nuetral saefty switch? what should i check? its a 88 5speed

 

88Stangboy

Banned

Dec 12, 2005

342

0

0

Greenville, SC

Jan 30, 2006

#2

• Jan 30, 2006

• #2

You try jumping it off or charging the battery?
Had the same problem in a truck with 351C and thought the
solienoid had went bad, turned out the battery went dead
cause the belt that turned the alt. had came loose and wasn't
charging the battery, try charging the battery or jumping it off.

 

fox racer

Member

Jun 22, 2004

577

0

16

Staten Island, NYC

Jan 30, 2006

#3

• Jan 30, 2006

• #3

if it were the NSS the starter wouldnt even click. i agree with 88StangBoy, try getting a different battery.

 

8

86bluecobra

Advanced Member

Dec 20, 2004

4,265

12

69

B.C. Canada

Jan 30, 2006

#4

• Jan 30, 2006

• #4

try this link
http://bellsouthpwp.net/l/r/lrichker/index.htm
rich has info there for yah to read

 

HISSIN50

"How long does it take to get help in here?

15 Year Member

Nov 29, 1999

31,179

33

129

Jan 30, 2006

#5

• Jan 30, 2006

• #5

Agreed with above. Joe is right about the solenoid. And I like the primary power system checking - battery, battery cables, cable to the solenoid, motor ground, etc.

One can use a jumper cable in parallel with an existing cable. If the car starts with a particular cable being assisted by the jumper, that cable and its connections are a place to look.

Good luck.

 

rd

Founding Member

Jan 12, 2000

3,316

63

109

Ocean Springs MS

Jan 30, 2006

#6

• Jan 30, 2006

• #6

In the typical case of Ford no start, I would clean all of the battery cable connections, pos and neg, especially the block end of the grounds. Make sure you have a good body to engine ground.

YOu can also jump across the starter relay terminals if this is an old school starter and relay. ( I just learned mini starters are wired differently yesterday)

If that does not improve it swap batteries. If that does not do it, change the starter.

This is assuming the engine will turn freely.

Every blue moon or so a cable will fail under the insulation at the molded clamp or somehthing, also.

 

B

blue87lx

New Member

Apr 23, 2005

175

0

0

Jan 31, 2006

#7

• Jan 31, 2006

• #7

car turns over by jumping solinoid but i get nothign when i use the key

 

JBeezy53

Member

Dec 28, 2003

559

1

17

Sacramento, Ca

Jan 31, 2006

#8

• Jan 31, 2006

• #8

First check all charging system connections, then try jumping it.

 

JBeezy53

Member

Dec 28, 2003

559

1

17

Sacramento, Ca

Jan 31, 2006

#9

• Jan 31, 2006

• #9

blue87lx said:

car turns over by jumping solinoid but i get nothign when i use the key

Click to expand...

Are you sure its clicking when you turn the key? If not check the ignition switch.

 

HISSIN50

"How long does it take to get help in here?

15 Year Member

Nov 29, 1999

31,179

33

129

Jan 31, 2006

#10

• Jan 31, 2006

• #10

blue87lx said:

car turns over by jumping solinoid but i get nothign when i use the key

Click to expand...

How did you jump the solenoid? By connecting the S-terminal to the battery lug, or by connecting the battery lug to the starter cable?

Good luck.