• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

still no start

  • Thread starter Thread starter stangman16
  • Start date Start date Jul 6, 2007

stangman16

Active Member
Nov 16, 2004
640
4
29
San Antonio, TX
Jul 6, 2007
#1
  • Jul 6, 2007
  • #1
Okay, I'm still not able to get this '66 stang 5.0 EFI to start after I installed a brand new fuel pump - which this time is correct for EFI applications.

I have spark at plugs - verified it's a blue spark
I hear the fuel pump prime every time I turn the key to the Run position from Off
Injectors firing as indicated by noid light

I spray starting fluid and the engine fires briefly but does not actually start up. Afterwards the garage kinda smells like ether. I have ensured it was at TDC on the compression stroke with the distributor stabbed and the rotor pointing at the #1 plug wire on the cap. I set the timing at 10° BTDC before trying the ether and it just cranks and cranks.

The only thing I can think of, since it fires briefly when the ether is sprayed, maybe the injectors are gummed up not allowing the fuel to pass through them?

I'm running out of ideas...... all suggestions welcome.
 

jammer84_03

New Member
Nov 30, 2003
468
1
0
Jul 6, 2007
#2
  • Jul 6, 2007
  • #2
sure you have fuel pressure?
 

stangman16

Active Member
Nov 16, 2004
640
4
29
San Antonio, TX
Jul 6, 2007
#3
  • Jul 6, 2007
  • #3
new fuel pump, I don't have a schrader valve to check pressure for sure though. I did disconnect the vacuum line from the regulator and fuel did not escape from it - so I assume that it's working okay.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 6, 2007
#4
  • Jul 6, 2007
  • #4
The symptoms point to no fuel pressure. Do you have an adjustable fuel pressure regulator?
 

stangman16

Active Member
Nov 16, 2004
640
4
29
San Antonio, TX
Jul 6, 2007
#5
  • Jul 6, 2007
  • #5
No, it's the stock type fuel pressure regulator. UNK how old it is though...

----

Here's the details on the pump I bought - I asked the counter guy three times if it would have at least 40PSI and he told me yes... (because he was trying to sell me an in-tank fuel pump after I asked for inline a couple of times) I just want to be sure on that:

Specifications for 510-12-920:
# Can be used with throttle body or multi-point injection
# Can be used on forced induction applications
# 80 GPH flow @ 15 PSI (at 13.5 volts)
# 480 PPH flow @ 15 PSI (at 13.5 volts)
# 5 amp current draw @ 15 PSI
# 67 GPH flow @ 45 PSI (at 13.5 volts)
# 402 PPH @ 45 PSI (at 13.5 volts)
# 8 amp current draw @ 45 PSI
# Supports throttle body injection up to 800 HP
# Supports multi-point injection up to 700 HP naturally aspirated
# Supports forced induction, multi-point injection up to 600 HP
 

troyGT03

New Member
Feb 22, 2004
278
0
0
too close to memphis,tn
Jul 6, 2007
#6
  • Jul 6, 2007
  • #6
not sure about your harness to the computer. the computer will not let the engine run until it sees a tach signal above a certain rpm and at that point it keeps the fuel pump running. strype will give you low down on this. edit check your fuel pressure.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 6, 2007
#7
  • Jul 6, 2007
  • #7
Here's the answer to no schrader valve on your fuel line...

Bullet piercing valve BPV 31. Available at most refrigeration supply stores and on ebay ( http://cgi.ebay.com/NIB-Supco-BULLE...-5-16-3-8_W0QQitemZ250137745564QQcmdZViewItem ) for $4.



It pierces the tubing and then allows you to measure the fuel pressure inside. Once it is installed you cannot remove it unless you plan to braze the hole punched into the fuel line. It's normal use is to service refrigeration systems that run at higher pressures that your EFI system. Properly installed, there is a very low risk of leakage. The connection port on it is a 45 degree flare fitting that will mate to the common tubing fittings found at hardware and auto parts stores.

I recommend that if you decide to try this, that you test it out on a piece of spare copper tubing first. The steel tubing for the fuel line is very hard and the piercing mechanism may not punch through the tube. Using copper tubing will enable you to make a sample punch and then measure the punched hole with the shank of a drill bit. Then you can drill a same size hole in the fuel line and install the tap.
 

stangman16

Active Member
Nov 16, 2004
640
4
29
San Antonio, TX
Jul 7, 2007
#8
  • Jul 7, 2007
  • #8
troyGT03 said:
not sure about your harness to the computer. the computer will not let the engine run until it sees a tach signal above a certain rpm and at that point it keeps the fuel pump running. strype will give you low down on this. edit check your fuel pressure.
Click to expand...

I don't have a tach hooked up at all... guess I need to invest in one?
 

stangman16

Active Member
Nov 16, 2004
640
4
29
San Antonio, TX
Jul 7, 2007
#9
  • Jul 7, 2007
  • #9
jrichker said:
Here's the answer to no schrader valve on your fuel line...

Bullet piercing valve BPV 31. Available at most refrigeration supply stores and on ebay ( http://cgi.ebay.com/NIB-Supco-BULLE...-5-16-3-8_W0QQitemZ250137745564QQcmdZViewItem ) for $4.



It pierces the tubing and then allows you to measure the fuel pressure inside. Once it is installed you cannot remove it unless you plan to braze the hole punched into the fuel line. It's normal use is to service refrigeration systems that run at higher pressures that your EFI system. Properly installed, there is a very low risk of leakage. The connection port on it is a 45 degree flare fitting that will mate to the common tubing fittings found at hardware and auto parts stores.

I recommend that if you decide to try this, that you test it out on a piece of spare copper tubing first. The steel tubing for the fuel line is very hard and the piercing mechanism may not punch through the tube. Using copper tubing will enable you to make a sample punch and then measure the punched hole with the shank of a drill bit. Then you can drill a same size hole in the fuel line and install the tap.
Click to expand...

Should I invest in a new OEM style fuel pressure regulator from advance, since they are fairly cheap at the parts stores? I have no idea where to get the above part, other than order off ebay and wait for it to arrive... but I need to be working on this thing tomorrow & Monday when I am off from work.

And if it's not the pressure regulator prohibiting the fuel from reaching the engine - are the injectors possibly bad? Is there any way I can test them? I do have a set of injectors that came off my friends '96 Mustang GT that I could try also, they look fairly clean. The injectors I have on there now came with the fuel rails, so I'm not even 100% sure if they work. But the other one's I have worked when we took them off his car a couple of months ago.
 

enyawix

Member
Dec 18, 2005
507
0
19
127.0.0.1
Jul 24, 2007
#10
  • Jul 24, 2007
  • #10
Use this check list

http://forums.stangnet.com/showpost.php?p=6161267


It "WILL" get your car running if you use it word for word
 
You must log in or register to reply here.

Similar threads

Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
520
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
598
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
N
Engine 86 GT no start/stall
  • nweber
  • Jul 28, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
279
Fox 5.0 Mustang Tech Jul 29, 2026
AeroCoupe
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
242
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?