• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Stuck lug nut!!!!!!!

  • Thread starter Thread starter dcurtis
  • Start date Start date Apr 18, 2008

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Apr 18, 2008
#1
  • Apr 18, 2008
  • #1
Ok, I just bought all new bearings and seals for my front end and while removing, or trying to remove my wheel I got 3 of the lugs off very easy like normal and the last one decided to just sit there and spin, the lug nut and stud are locked together, I tried it after words with the impact wrench just hoping it would work and now I can spin the lug and stud with my finger, so my question is, what would be the best way to get it off???
I thought about just cutting the center cap off somehow and removing the whole thing together but I don't know if the caliper would let it?
Or should I just be very careful and cut the lug off, remove the wheel, remove hub and the cut the stud off and replace the stud? I'm so pissed off right now that I could just put the other lugs back on it and sell it, Not, it's just a small problem but it's a very frustrating one. Any opinions on the best way to go about removing it, the lug did unscrew about a 1/4 of the way before the stud started spinning with it, so I could cut it off if Im careful
 
S

STP72

New Member
Nov 11, 2006
109
0
0
Apr 18, 2008
#2
  • Apr 18, 2008
  • #2
I was going to say heat it up and use some penetrating oil but that won't work. If your careful I would just cut it off and in stall a new stud
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,075
1,658
194
NJ
Apr 18, 2008
#3
  • Apr 18, 2008
  • #3
You should be able to get the spindle nut off, along with removing the caliper bracket from behind, then do whatever it takes from the back side of the rim/rotor.
The rotor is shot now, regardless you need a new one, besides it will only be like $40.
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Apr 19, 2008
#4
  • Apr 19, 2008
  • #4
Just got it off , I just stuck a 4-way on that lug and jumped on it, it snapped the lug off right at the shank , and it turns out that the lug nut had just striped somehow, I still don't know, the rotor is fine though, I think it was just because the stock studs weren't grabbing enough of the weld lug nuts, I am just going to get some new studs and replace every one front and rear, but I will be getting studs that are at least a 1/2 inch longer, so does any one know if a parts store has longer than stock studs that will work, I don't really have time to wait on some to be shipped from summit or anywhere else, I have to be at work Monday, and the stang is my only mode of getting there. Well I am going to run to Oreilly's and see if I can find some longer studs, hopefully they will have something there so I won't have to wait on some to be ordered, well come to think I may as well order them because I now need 2 new lug nuts anyhow, and I know the parts store doesn't carry weld lugs, at least I doubt they do.
 
You must log in or register to reply here.

Similar threads

J
Exhaust manifold to Y-pipe nut & stud dimensions?
  • joeybuddy96
  • Jul 7, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
219
SN95 V6 Mustang Tech Jul 9, 2026
joeybuddy96
J
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
712
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
A
79 mustang pace car spoiler.
  • Anglosaxon83
  • Feb 21, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
272
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 21, 2026
Anglosaxon83
A
8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
630
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
719
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?