• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-

Suspension and alignment

  • Thread starter Thread starter eortegaiii347
  • Start date Start date Aug 14, 2009
E

eortegaiii347

New Member
Aug 14, 2009
0
0
0
San Benito, Texas
Aug 14, 2009
#1
  • Aug 14, 2009
  • #1
I am at my wits end here. Any help would be greatly appreciated. I have done alot of work restoring my 1966 mustang. Well ever since I have put it back together I can seem to get the alignment to set right. I have taken it to multiple aligment shops and still no luck. It seems that if I drop the nose it works fine when driving. If I try to take off quite fast as the weight transfers to the rear the nose comes up ans when that happens the alignment seems to go out of whack. I really dont know why this is happening. The mechanic told me that he ha no idea why it is doing that either. All the numbers match up. Now i have made the engine lighter by using aluminum heads. Most of the steering and suspension has been done with the OE replacment stuff. I am really at a loss here. Some say the chassis might have some twist some say the engine is too light for the stock springs some say it might have the wrong ride height up front. I am really at a loss. Any help would be greatly appreciated.
 

Az Pete

10 Year Member
Mar 30, 2005
711
18
49
Panama City, Fl.
Aug 14, 2009
#2
  • Aug 14, 2009
  • #2
Not sure what specs you are using. I have the same problem after some front end work. I have severe bump steer with hard acceleration. Also, it is critical to know what front end parts you have such as possibly Granada spindles. These create more bump steer and need a kit to fix the problem.

I have been told I need to get things to these specs: Goes to shop next week.
"0 - camber on both sides,
2 deg. positive caster on both sides,
1/8" toe-in.
The caster and camber has to be the same on both sides. DO NOT let them set the car for road crown."

This came from Opentracker Racing Products (Opentracker Racing Products) since I have his products under my car.
 

rbohm

Founding Member
Apr 12, 2002
6,698
550
204
tucson,az
Aug 14, 2009
#3
  • Aug 14, 2009
  • #3
two possibilities here that i can think of;

1: when you tightened the front suspension bolts for the lower control arms, you did it while the car was up in the air. that causes a binding in the return travel for the suspension.

2: more likely without knowing what you combination is, you used granada spindles and did the shelby mod. this can cause the very binding you are experiencing. it isnt always the case as some granada spindles have geometry closer to the stock spindles.
 

latamud

Founding Member
Oct 22, 2002
791
2
19
Tampa, FL
Aug 14, 2009
#4
  • Aug 14, 2009
  • #4
rbohm said:
two possibilities here that i can think of;

1: when you tightened the front suspension bolts for the lower control arms, you did it while the car was up in the air. that causes a binding in the return travel for the suspension.

2: more likely without knowing what you combination is, you used granada spindles and did the shelby mod. this can cause the very binding you are experiencing. it isnt always the case as some granada spindles have geometry closer to the stock spindles.
Click to expand...


I agree with #2, this happened to 2 people i know with Granada swap and Shelby drop. When they drive forward the front end rises like a boat in water. But when the car stops, the front end stays up. We cut the front coils a little and it stopped the rising effect.
 

krash kendall

Active Member
Nov 19, 2004
1,258
0
36
Aldergrove, B.C. Canada
Aug 15, 2009
#5
  • Aug 15, 2009
  • #5
Since you didn't mention a Granada conversion...

I only ask if the OEM parts that were replaced are the correct ones. Specifically, are the strut rods '65-'66 or are they '67 or up? I have seen the wrong ones subbed in with the results you describe.

FYI: The early ones have threads that stop when fully installed, the later ones have continuous threads for full adjustability.

I honestly don't have a clue what your car has up front, this is just something I have seen in the past.
 

Az Pete

10 Year Member
Mar 30, 2005
711
18
49
Panama City, Fl.
Aug 16, 2009
#6
  • Aug 16, 2009
  • #6
I just set my alignment to the specs I listed above. All is well now. Car drives great. The car had neg. caster which caused the problem. I highly recommend the listed specs.
 

HistoricMustang

Active Member
Apr 11, 2003
2,359
0
46
Confederate States of America
Aug 21, 2009
#7
  • Aug 21, 2009
  • #7
This might help as I never had the binding problem so many people talk about. Get her low and put up with somewhat of a "rough" ride.

You can not have your cake and eat it too. With these things it is all about compromise.

Click here, it won't cost you a dime!

http://www.historicmustang.com/tech.html
 
You must log in or register to reply here.

Similar threads

L
2001 cobra sequential tail lights
  • lking78
  • May 26, 2026
  • SVT Tech Forum
Replies
4
Views
185
SVT Tech Forum Jun 14, 2026
lking78
L
L
Help with 1986 GT 5 Speed Please
  • Lcasada1999
  • Mar 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
267
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Strut Tower Help!
  • 93Nifty
  • Jan 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
28
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 28, 2026
General karthief
G
Idle surging after warm up
  • GALLY3309
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
130
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 10, 2026
Noobz347
D
2006 GT Windshield Cowl install
  • Daddidio
  • Mar 12, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
202
2005 - 2009 Specific Tech Mar 12, 2026
Daddidio
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?