• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

timing problems

  • Thread starter Thread starter stevesLX
  • Start date Start date Mar 8, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 8, 2007
#1
  • Mar 8, 2007
  • #1
I think I have some timing issues going on also. The way my balancer is set up is I have the the following marks going from left to right if you are looking at it to set the timing: 10 C 0 T 10 20 30 40.


I have my timing set at 14 with spout out. Its basically set between the 10 and the 20 marks. I guess this is before TDC I am not sure. I know if I turn my distributor to the left like towards the altenator it smooths out but if I move it to the right towars the battery it gets really rough. But right now the car just doesn't act right all the time. At times you can floor it and it just doesn't have any power it lags but then it will take off on you at other times. It seems like its differen't from one traffic light to the next. The other thing it will do from time to time is if you stomp on it from the get go it will run half way decent but if you drive normal and then go to stomp on it it will lack power sometimes. You have to let off the pedal and then stomp it again. Any ideas as to whats going on here and am I setting my timing right?
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 8, 2007
#2
  • Mar 8, 2007
  • #2
I guess no one knows anything that could be causing this intermittent power loss here and there. And if my timing is set correctly?
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Mar 8, 2007
#3
  • Mar 8, 2007
  • #3
It sounds like you are following the right steps for setting up the timing. Your timing pointer could be bent, but your problem really doesn't sound like its a timing issue since it does it intermittently.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 8, 2007
#4
  • Mar 8, 2007
  • #4
any ideas as to what it could be. My motor is pretty much stock w/ the exception of 24# injectors 65CFM MAF and a Edelbrock 5.0 performer intake. It also has a 75mm BBK throttle body and spacer. I have been told that TB is to big for the set up and that I also dont need that big spacer on there either. This was all here when I bought the car. It also has a 303F cam. I am new to all this stuff.
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Mar 8, 2007
#5
  • Mar 8, 2007
  • #5
Well, you usually want your MAF to be larger than the throttle body and egr spacer. With the setup you have, I would expect the powerband to be in the higher RPM range. Does it seem like slow throttle respose or an engine miss?
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Mar 8, 2007
#6
  • Mar 8, 2007
  • #6
Throttle position sensor on its way out??
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 8, 2007
#7
  • Mar 8, 2007
  • #7
I'd give the timing one more check. If it's too retarded, it will bog like that. Not to offend, but I have to ask:
When you set the timing, you had the SPOUT connector removed? Otherwise, you are running real retarded.

For diagnostics, I will twist the dizzy (SPOUT installed since no timing gun is being used) till the car runs better, ignoring the marks on the balancer (a spun balancer makes for a poor point of reference anyhow).
WHen I find the sweet spot performance wise, I check timing just to see where I have it.

EDIT: If you use this method, be sure to keep an ear out for detonation (as should be done anytime timing is advanced).

Good luck.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 8, 2007
#8
  • Mar 8, 2007
  • #8
O.K. yes I had the spout out and I always hear that term of detonation what exactly does detonation sound like? What kinda noise am I listening for? It idles pretty rough you can definitely hear it miss. And when you drive it almost feels like it loading up at times and when you stomp it and it just has no power but at other times it runs like a champ
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Mar 8, 2007
#9
  • Mar 8, 2007
  • #9
Steve,

Have you checked for codes yet? Is your check engine light on, or does it come on sometimes? You can have stored codes without the CEL being on.

You can buy a code scanner for about $30 at auto parts stores, or you can do the free method. Do a search for "codes", and find jrichkers post detailing how to pull codes for free. It's pretty simple.

Jeff
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 8, 2007
#10
  • Mar 8, 2007
  • #10
I took the car somewhere awhile back and they struggled with it for a whole day trying to get codes out of it. My check engine light is disconnected. I dont even know where the wiring is for it to even try to hiik it back up. The guys before I owned it hacked it.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 9, 2007
#11
  • Mar 9, 2007
  • #11
Steve, is the self test connector still in place under the hood (and hopefully unmolested)? It will be a trapezoidal connector in the back driver's side corner of the engine compartment. If it's okay, you can use a reader like Jeff noted or even a test light (SD cars dont have a functional CEL, so they have to use one of these other two methods. You can do the same).

Detonation sounds like marbles being agitated in a coffee can, and as it worsens, it sounds like marbles in a glass jar.

Good luck.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Mar 9, 2007
#12
  • Mar 9, 2007
  • #12
Yes I actually have the big connector itself and 2 single connectors on the drivers side corner. They are all in the same harness. I have a volt meter with the needle. Which one of those single conectors do I want to jumper to or probe.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 9, 2007
#13
  • Mar 9, 2007
  • #13
stevesLX said:
Yes I actually have the big connector itself and 2 single connectors on the drivers side corner. They are all in the same harness. I have a volt meter with the needle. Which one of those single conectors do I want to jumper to or probe.
Click to expand...

Be real careful when pulling codes. IIRC, there is a black colored single-wire connector next to the single grey-colored one. The black wire has 12 volts going through it!
Anyhow, see Jrichker's post for code retrieval. Also, if you have a repair manual, the emissions chapter should have pretty detailed instructions.

Good luck.
 
You must log in or register to reply here.

Similar threads

Strange timing issue
  • 92 Bimini Blue
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
22
Views
767
Fox 5.0 Mustang Tech Oct 20, 2026
rednotch
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
352
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
347
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
249
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
A
Electrical electric mirror switch issue...
  • alchemist1
  • Apr 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
192
Fox 5.0 Mustang Tech Apr 19, 2026
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?