where to get a 351?

blkstangman88

New Member
Apr 6, 2004
646
0
0
i was looking into getting a 351 and stroking it to a 408.......well would it better to get a used on or a brand new one? and where would be the bast place to get the block and strocker kit?
 
Depends on cost. Used blocks are cheaper. Dart makes the baddest small block made. It is going to set you back $1800-2000 just for the block. Good thing is that it is boost/ nitrous ready and you can go bigger than 408 with ease.

Eagle or Scat can provide the crank and have total rotating assemblies as well.
 
Here's how I did it.

I picked up a complete 1974 351w from a wrecking yard. Brought it home and stripped it to a bare block. The block went to the machine shop for cleaning and inspection. The shop also drilled and tapped the holes for the roller lifter spider. I don't think they even charged me for the drill and tap. About 500 for the motor and 225 for the machine shop.
I also found a local place that preps bores out used blocks and puts them on a shelf until needed. You would still have to get the bores honed for your pistons and then cleaned, but it still would have been cheaper to go this route. The reason I did not buy the block off the shelf was that they did not have any old blocks (pre 74). The older blocks have a reputation for being a little stronger due to higher nickel content. The 69 block is considered the best due to its nickel content and thicker main webs. (If anyone reads this and disagrees please let me know, as I tend to forget number stuff)
The rotating assembly came off a shelf from an ebay store. I was able to specify dished pistons, and all forged internals. The only thing I regret is not being more careful about the piston rings they selected for me. I ended up with low tension rings, which translates to 20% blow-by. That put so much pressure in the crankcase that oil would blow out of the dipstick tube.
Putting the motor together was fairly simple. Just go slow and measure every clearance you can. Recording all clearances will help put you at ease when you turn the key for the first time and wonder if the valves will hit the pistons. I recommend finding a book for first timers, it helped me a great deal.
Don't try to reuse an oil pump or timing chain. They are far too cheap to run the risk of failure. I did try to reuse the oil pump on the first build. When the motor was in the car I tried to prime the oil system. Nothing happened, so out came the motor to replace the pump. I suggest priming the oil system while the motor is still on the stand.

Let me know if you have other Q's. I would be glad to help get another 408 on the road.
 
blkstangman88 said:
the dart blocks from jegs any good? if so, what one?

That is the same block that we are talking about. The iron eagle blocks are good well over 1000 hp. 2500 for them though. I guess the steel cost went up.




There is also the new Man O War Ford Block. Dont know the difference from the Man O War to the Iron Eagle. The Man O War does have 6 head bolts per cylinder. Need heads with 6 holes for it to work.

http://www.electronic-pr.com/pr/new_wp_270.html
 
hllon4whls said:
That is the same block that we are talking about. The iron eagle blocks are good well over 1000 hp. 2500 for them though. I guess the steel cost went up.




There is also the new Man O War Ford Block. Dont know the difference from the Man O War to the Iron Eagle. The Man O War does have 6 head bolts per cylinder. Need heads with 6 holes for it to work.

http://www.electronic-pr.com/pr/new_wp_270.html

hllon,I got the 9.5 deck DART Iron Eagle block in my car.408, Eagle stroker kit w/ the up grades.

The block is a absolute beast.It got 4 bolt BILLET STEEL main caps on all five,better oil system and is dry sump oil compatiable.The cyclinder walls and decks on this thing are TTHHICK!The pan rails are beefy to and the block has ribbing in the back (bell housing area).It also has 4 more freeze plugs,two in front,two in back that are extra from a stock block.

Its sweet,but they got a more economical "Sportsman block" that is good to 1500hp!And its only around $1800.
 
I think it would depend on your goals weather or not to get a dart or world block, or R block for that matter. I have seen some wicked 351W's using a factory block. I am sure they have nothing on the aftermarket blocks but I think for someone to spend all thier money on a dart/world/R block for a basic street buildup would be excessive.

Sportsman handling 1500hp, I thought they slit right up the center just like stockers do.
 
90mustangGT said:
I think it would depend on your goals weather or not to get a dart or world block, or R block for that matter. I have seen some wicked 351W's using a factory block. I am sure they have nothing on the aftermarket blocks but I think for someone to spend all thier money on a dart/world/R block for a basic street buildup would be excessive.

Sportsman handling 1500hp, I thought they slit right up the center just like stockers do.

Yea,the ford Sportmans block are basicly a early model stock block,but Im talking about the DART Sportsman block.MUCH MUCH stronger than a FRPP Sportsman block.

Edit: And Im not bais,I had a 357 (.030 over) 74' 351W,that was pretty damn fast,and this new motor blows it away.
 
id much rather spend the extra $500 or so on a much better block the first time then build a combo and tell my self later "i should have do that"

So my goal is to get my block in the next couple months and the 408 stroker soon after, only problem is it takes me some time to save....lol

Anyways, wheres a good place to get the stroker kit from? i have a local shop ive heard many good things from. another question is, whats a good H/I/C combo for this, im planning to get dished pistons for a S/C or turbo set up, cars not really going to be street able but mabe.