• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

White Gauge Face Install

  • Thread starter Thread starter Get E Up 98
  • Start date Start date Nov 14, 2004

Get E Up 98

New Member
Apr 18, 2004
144
0
0
Nov 14, 2004
#1
  • Nov 14, 2004
  • #1
How hard is it to do? I Know you have the needles you have to be careful with. Any ideas, tips, suggestion for this install?
 
G

gt281ci

New Member
Nov 9, 2002
14
0
0
mass
Nov 15, 2004
#2
  • Nov 15, 2004
  • #2
i did it with mine, take your take and be precise(i wish i did) my gas gauge way off and same with my temp gauge, but it can be done if you take your time! and just my opinion it doesnt look that much better(even though i did it)
 
B

Blue70

Active Member
Nov 1, 2004
160
28
38
Wilmington NC
Nov 15, 2004
#3
  • Nov 15, 2004
  • #3
Check out the link HERE

It shows some real good instructions.

I just did mine, I took a bunch of pictures first, some while driving, some at idle, some with the car cold and the key on.

I was able to set the 4 outer gauges with the key on and the car cold, just wait for a while to do the gas gauge, it takes a while to come all the way up. Then I set the Speedo, I had a friend set his Cruise control at a whatever speed, then I was able to put my needle on while following him at that speed. After that was set I went back to my pictures and found out what I was taching at different speeds, I brought it up to that speed and set my tach needle, then double checked it at other speeds that I had taken pictures of. (First I tried to just set the tach and speedo against the stops, but they were off, do NOT trust that route!!)

 
You must log in or register to reply here.

Similar threads

M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
167
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
A
A/F ratio gauge install questions.
  • AngryH58
  • Sep 24, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
230
1996 - 2004 SN95 Mustang -General/Talk- Oct 22, 2026
Noobz347
J
Fox Lost all gauge cluster function after Holley Terminator X install
  • Justin17383
  • Monday at 4:57 PM
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
110
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Wednesday at 8:05 PM
LILCBRA
F
3G Alternator install question
  • fathead429
  • Oct 24, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
7
Views
245
1974 - 1978 Mustang II Talk & Tech Oct 25, 2026
LILCBRA
K
Electrical 2000 GT Intermittent Engine Shutdown In Motion - DTC U1262
  • kenster1092
  • Apr 13, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
337
SN95 4.6L Mustang Tech Apr 24, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?