Search results

  1. sdc13

    car scared bejeezuz out of me last night!

    Last week I put my stang back on the road after sitting idle for 2 years. The first week I pretty much babied it around. Well last night I went WOT for the first time. When I let off the gas to go to 2nd gear the revs shot up to redline like the throttle was stuck open. It didn't hit a rev...
  2. sdc13

    installed bassani x-pipe

    After 2 years of my stang sitting non-op in my driveway I am putting it back on the road. I installed a bassani x w/cats to pass emissions. The bassani is much quieter than my old o/r h-pipe. I thought the x was supposed to sound more "exotic" but it really just sounds like a quiet h-pipe. I...
  3. sdc13

    Black wheels on black stangs...get in here.

    I'm thinking about doing 18x9 and 18x10.5 black rims on my black vert. I like rims with the polished silver lip and deep dish in the back. The only design I don't like are bullets, not into the retro look. Please post pics of your black rims. I'm looking for ideas.:D
  4. sdc13

    Cobra brake upgrade

    Just got done installing a set of cobra 13" rotors, cobra calipers and ss lines. The car brakes much better now. The pedal feel is a lot firmer which I like. Definitely recommend this upgrade:nice:
  5. sdc13

    Damn brake lines.....HELP!

    So today I was supposed to switch out my front springs and put on the cobra 13" calipers rotors and ss lines. I was feeling pretty good about myself after I finished the springs and had the rotors and calipers on. When I tried to remove the stock brake lines I couldn't for the life of me get the...
  6. sdc13

    Go with aluminized or stainless Bassani X?

    I'm ordering a Bassani X-pipe w/cats this weekend. Should I go with the stainless or the aluminized ones? The stainless is $150 more. Since I live in Southern Cal. do I need to go stainless?
  7. sdc13

    What do you guys think of this....

    Does this sound to good to be true? Only 15300 miles... http://cgi.ebay.com/ebaymotors/1997-Ford-Mustang-Cobra-Supercharged-450HP_W0QQitemZ4608318802QQcategoryZ6236QQrdZ1QQcmdZViewItem
  8. sdc13

    Looking for X-pipe sound clips...

    Wondering if I should change my o/r h-pipe to an X. Can anyone post some sound clips?
  9. sdc13

    Those with G-force trans-need opinions

    I'm thinking about upgrading to a g-force t-5 when I pull the stock motor and drop in a 331/347 stroker in a few months. How do you guys like the tranny? Will it hold 450rwhp? Lets hear some opinions...
  10. sdc13

    Installer/tuners in Los Angeles area...

    Can anyone recommend a good shop in the L.A. area? I'm doing a new 331/347 (not sure yet) longblock this summer. I will also be uprading to 42# inj and new mass air so I'll need a tune to get it all running. I would prefer to get the combo installed and dyno tuned from one shop.
  11. sdc13

    cobra brakes...

    NE1 know if the cobra brake kit will clear my 17" tribars? I'll be upgrading the wheels later but problably not for a while. Merry Xmas...:)
  12. sdc13

    90mm MAF

    Will a Lightning 90mm MAF work with a stock ECU? I'm planning on a 331 stroker next summer and there are some good deals on 42#inj + 90mm MAF combos. If this won't work what do you guys suggest? With the demise of Pro-M will I be ok with a C&L 76mm on a blown 331?
  13. sdc13

    Fan question...

    I have a fluidyne radiator sitting in my garage that I can't install because the stock fan is too thick and hits the novi 2000 crank pulley. Does anyone make a low profile fan that will bolt up in place of the stocker?
  14. sdc13

    10.5" wheels

    Anyone have pics of 10.5" cobra R's on their car. Also, what size tire do you guys run on the rears?
  15. sdc13

    13" brake ?

    There is a company advertising a 13" brake (cobra?) upgrade kit for $399. The kit includes calipers, pads, rotors and steel braided lines. Is there anything else I need for the install like caliper brackets, spindles etc... or will this kit bolt right up?
  16. sdc13

    Which motor?

    Next year I plan on rebuilding my 95 top to bottom. My goal is a reliable 400 rwhp weekend car. I will be keeping my Novi 2000 from my current setup. I plan on keeping boost to 10#. My question is which motor to go with. I've narrowed it down to: 1: D.S.S. 306 pro bullet longblock w/afr heads...
  17. sdc13

    Timing ?

    I can't remember which way to turn the dist. Got some pinging I need to get rid of. I think it's: Clockwise=retard Counterclock=advance. Please someone correct me if I'm wrong.
Top Bottom
Back
Forums
Menu