Search results

  1. DanG

    Advice On Selling Supercharged/stroked 1995 Cobra

    Hi all- I've come to a conclusion that I am going to need to sell my 1995 cobra. I simply do not have the time to dedicate to keep this car going, and would like advice on selling it. I am the original owner, and the car has 73xxx original miles. Therefore, what would be the best methodology...
  2. DanG

    Help get my car back! Possible fuel issue

    I took my car into a local tuner about in August 2012 for a re-tune after installing a different supercharger ( D1SC -to-D1 ) arger fuel injectors, and having a Pro-M 3" pro-tube re-calibrated for the new sized injectors. From the beginning there were a slew of problems that never existed...
  3. DanG

    Taking Car For Dyno Tune On 8/4.

    Looking forward to taking my car in for another dyno tune next weekend on Saturday 8/4. I don't believe the car will be tuned on Saturday, rather it is a drop-off date to review my most recent combination changes with the tune. The car is getting tuned again at Md Performance Center in...
  4. DanG

    Drivetrain Clutch Issues- Need Assistance With Adjustment

    I need some assistance tracking down a clutch issue which I'm having problems identifying. I must have installed a clutch and adjusted the cable correctly a dozen times in the past, however I can't seem to get this right time time around..... To start, I noticed that it became difficult to shift...
  5. DanG

    Electrical 12 Volt Dedicated Circuit

    I'm in the process of installing a Snow Methanol kit, and am to the point where I am finishing up the electrical work. My next step is to connect the controller to a preferred 12 volt key on circuit, fused for 10-15 amps. With that said, I'd like to know the correct process to getting this...
  6. DanG

    Forced Induction Many Thanks To Ati Procharger

    First of all, I wanted to start this thread out by saying that ATI Procharger has went well above and beyond the call of duty to satisfy me as a customer, and has exceeded my expectations by their customer service. In short, I say this because I have owned A D1SC head unit for approximately 9...
  7. DanG

    MSD 50lb EV1 high impedance injectors

    Have a set of 8 MSD 50lb high impedance injectors, with EV1 style connectors. ( Stock connector type ) $225 to your door. I accept Paypal, money order, or certified check.
  8. DanG

    After spring/shock install, banging sound from rear

    Hi all, I just finished an H&R race spring and Bilstein strut installation which seemed to go pretty smooth. However, when I take off in 1st gear, I hear a knocking/banging sound from the rear of the car. I have verified that all of the bolts are tightened and torqued down; stocks, lower...
  9. DanG

    How to properly run a compression test

    Been a while since I've run one of these, however, I wanted to make sure I'm not missing anything before I begin. 1) disconnect coil wire from distributor 2) disconnect fuel pumps ( I have externals ) power supplies 3) put throttle body blade in wide open position, or simply put pedal to floor...
  10. DanG

    Exhaust from one tailpipe smells of coolant.

    As some of you may notice, I've been posting quite a bit on here lately, as I am just getting back in the mustang scene from years off, and am running down a few issues along the way. Many thanks to those who have assisted me with the issues I've run into thus far. :) I've been noticing the...
  11. DanG

    Battery choice for 1000 cranking amps?

    I currently have a battery installed in the trunk which offers 550 cranking amps, but often turns the car over slowly. I have the battery grounded well, and also have a power cable running from the battery directly to the alternator for better charging of the battery. I'd like to install a...
  12. DanG

    Over flow coolant tank level question

    Long story short, I got the car back from the dyno a few weeks ago, where the shop also finished off a few odds and ends for me, including initial start up of the car after 8 years, evac system install for the valve covers, and pour in coolant. ( I gave them the car w/o coolant in the event...
  13. DanG

    H&R Race Spring performance

    In another post, I've been speaking about a coil over setup for my car, however, I'm also considering an alternative, to purchase the H&R Race springs along with Billstein shocks in order to get my ride height a little lower, as well as improve the current ride quality, as my stock shocks are...
  14. DanG

    Towing lowered cars

    In the near future, I plan to install a new suspension package which will end up lowering my car about 1.5" in the front, and perhaps a little less in the rear. I currently have the stock dune buggy ride height. My concern, is if the car ever has to be towed on a flatbed, how could this...
  15. DanG

    Pulley alignment issue

    I've been having an issue with a pulley alignment problem, where my belt, albeit extremely tight, walks forward on the tensioner and the water pump pulleys. ( The only pulleys without a lip. ) Thus far, it appears the smog pump pulley is pushed forward about 1/8" further than the crank...
  16. DanG

    White smoke from breather

    Noticed today when I started the car up, that I have a little bit of white smoke coming from the valve cover breather hole, which is normally plugged with an evac line which runs to a catch can. I understand white smoke can mean water being burned in the combustion process, or worn rings...
  17. DanG

    331-Procharger dyno sheets

    I got around to scanning the dyno sheets from the latest dyno pull which was conducted on a Superflow dyno with eddy brakes. Max power came at 6300rpm: 510.8 Max torque was at 5,200rpm: 471.5 Max boost seen was about 12.6psi @6300rpm. Car drives well, and feels pretty strong. I'm going to...
  18. DanG

    Normal engine operating temperature

    Hi all, I feel like an amateur asking this question, however it's been years since I've been in the car realm, and am trying to get back up to speed. Anyways, I wanted to verify what a normal motor operating temperature would be for in-town/stop-and-go traffic? Currently, I've noticed...
  19. DanG

    DGR Performance in Dillsburg

    Hello, Does anyone know if DGR performance ( Formally Kauffman's and SGS auto ) is still in business? I've been trying to get a hold of these guys for about a week via email and phone, with no such luck. Just wondering.
  20. DanG

    Procharger power pipe

    Anyone using the AFM Procharger power pipe for the P1/D1 head units? Looks like a fairly nonrestrictive piece which could yield a decent gain for the price, particularly if a hood is actually a cowl hood with the opening at the rear. 13. Forced Induction Power Pipe®
Top Bottom
Back
Forums
Menu