Search results

  1. 8

    Supercharged Mark 8

    http://gtamc.com/forums/showthread.php?t=24706 :nice:
  2. 8

    BB Chevy w/powerglide in 89 GT

    Hey boys,check out this "project". http://gtamc.com/forums/showthread.php?t=24152 I don`t get it.:shock:
  3. 8

    Car stolen

    http://www.youtube.com/watch?v=m2bycZa4zKY :owned:
  4. 8

    Buddy Rich drum solo-1970,wtf...

    Any drummers here?Found this on youtube. This is insane.He`s 53 at the time as well. (he never took a lesson and refused to practise outside his performances):bang: http://youtube.com/watch?v=WgeX9iYOFSQ
  5. 8

    AVRO ARROW full scale model

    http://forums.stangnet.com/showthread.php?t=663491
  6. 8

    Broken E-brake cable

    The emergency brake cable that goes from the lever to the equalizer just broke on my 89. This is the short cable. Just wondering if anyone has done this and how much of a pita resetting the spring tension on the hand brake assembly is and how hard it is to reconnect the cable? Not looking...
  7. 8

    Electrical experts...blowing fuses

    A few days ago the factory radio and interior lights stopped working. The 15amp fuse that protects the courtesy lamps,key warning buzzer,fuel filler door release,radio,and power mirror was blown. I tried a new 15amp fuse and it blew the instant it made contact.A second fuse did the same...
  8. 8

    Best intake gaskets...Fel-Pro or Mr.Gasket?

    Which is the best intake manifold gasket set to go with,Fel-Pro 1250`s or Mr.Gasket Ultra Seal or Ultra Seal 2? Currently using the Fel-Pro 1250`s which suck imo.I`ve had to retorque the lower 4 times so far to stop coolant seepage.
  9. 8

    Throttle body coolant hose size?

    Anyone know the size of the throttle body/egr spacer coolant hoses?
  10. 8

    ASP 1-7/8" OD alt pulley on 1996 3g alt

    I already have a ASP OD alt pulley on the stock 75amp 2g alternator thats still in the car.I won`t be doing the swap till spring due to it being winter time here. The 96` and up 3g`s are a little different than the 94-95 pulley wise.(something to do with a revised case). My stock pulley from...
  11. 8

    Psssst.Brand new zero mile stock 5.0L HO roller cams

    Anybody looking for a brand new,0 mile stock 5.0L roller cam? Probably not,but if you are,I was looking over the Federal Mogul website for brake parts when I decided to look up camshafts for 89`5.0L Mustangs and see that they list the stock 5.0L HO roller cam,part #CS760,based on the original...
  12. 8

    Door hinge pin and bushing replacement

    My drivers side door needs new hinge pins and bushings. How much of a pita is it installing new ones?Any tips/tricks to make the job easier?(car is a 1989).
  13. 8

    73mm caliper upgrade on 89,5.0L Mustang with drum brakes

    To those who have done the 73mm front caliper upgrade on a 87-93,5.0L Mustang with the rear drum brakes in place,did you have any problems with a soft longer travel brake pedal afterwards? I would be using the following parts;1991 Lincoln Mark 7-73mm calipers,94-95 master cylinder,Maximum...
  14. 8

    3>2 port master cylinder conversion kits

    Anyone have any opinions/experience with some of the 3>2 port master cylinder conversion kits out there like Maximum Motorsports or Matt90GT`s kits? What`s the best one to go with?
  15. 8

    Crane Cams screw up...heads up warning

    Someone posted this on the Corral yesterday, www.corral.net/forums/showthread.php?t=686005
  16. 8

    What to use to pull a vacuum on AC system at home

    Anyone know of an affordable device/contraption you can use at home instead of going to a garage to pull a vacuum on the AC system?
  17. 8

    73mm brake caliper upgrade

    I`ve seen some posts recently about using 73mm Lincoln/Crown Vic front brake calipers on 87-93,5.0L Mustangs as they are a direct bolt on. My question to those who have done this is how much of an improvement in braking performance,(if any),does this swap provide???Is it worth it?
  18. 8

    AC suction low pressure service port location 89,5.0L

    Just want to double check the location of the suction,(low pressure)AC service port location on a 89,5.0L Mustang,for recharging purposes. Is it the fitting that`s right on the compressor,or the fitting that`s on the metal line just before the compressor?
  19. 8

    Fiore micro-click FW adjuster and quadrant

    I posted this before,but it got wiped out when stangnet crashed. Anyone running the Fiore firewall adjuster and quadrant.I see they`ve both been redesigned.Any experience/opinions with these parts???
  20. 8

    89` 5.0L Mustang 4guage 3g alternator power wire length

    How long approximately is the 4awg power cable on a 89,5.0L stang when doing the 3g 130amp alternator conversion?Does 8-9 feet sound about right?
Top Bottom
Back
Forums
Menu