Search results

  1. dcurtis

    Sweet car collection, almost all GM though

    I think it is a waste.
  2. dcurtis

    4.10s and aod tranny?

    When I did my gear swap I did no break in at all, I put them in and left my driveway sideways. :nice:
  3. dcurtis

    high volume oil pump question

    I agree, use the stock one, upgrade the oil pump drive shaft if you want to though.:nice:
  4. dcurtis

    AOD&what gears?

    I don't understand how people are getting worse gas mileage with the 373's over the 273's, when I swapped in my 373's my mileage got better:shrug:
  5. dcurtis

    4.10s and aod tranny?

    I say 373's, that's what I have and I like them except for the 2-3 shift comes almost instantly when I get on it, almost like going from 1st to 3rd on a hard launch, I couldn't imagine how short it would be with 411's. It's like 111111111-22-33333333-444444444444444444:shrug:
  6. dcurtis

    starter problem

    did you check your solenoid?
  7. dcurtis

    Fuel line question??? Rubber hose real or just for prtection over plastic hard line?

    Yeah, there is rubber over the plastic.:nice: Last time I dropped my tank to replace my sending unit I didn't make sure the fuel line was positioned away from the tire and I developed quite a fuel leak pretty fast, because the tire ate through the rubber and the plastic inside:notnice:
  8. dcurtis

    Performer Rpm intake

    How much for the heads and the intake together if you still have them? Any pics
  9. dcurtis

    Roush 200 steel heads

    Any pics, and what brand are the rollers.
  10. dcurtis

    Used Trick Flow parts for sale

    How much for the heads, roller rockers,, upper and lower intake, mass air and injectors shipped to 72830? and how much without the intake? Will the bolts be with it for the intake and heads?
  11. dcurtis

    You guys want a practice tree

    .439 first try. but still lame.
  12. dcurtis

    Slow throttle return

    +1 on possible vacuum leak.
  13. dcurtis

    Rear view mirror question

    Junk it, that is the reflective stuff behind the glass for the mirror. No fixing it.
  14. dcurtis

    idle

    You may need to pull and clean your iac valve:shrug:
  15. dcurtis

    Clean Fox, NOT COOL!!!

    I just read that while the yards can sell all of the parts of the clunkers minus drivetrain, they are only allowed 6 months for each car before it has to be crushed.
  16. dcurtis

    AOD Trans

    Did this happen after you changed filter and fluid or before? If after, I have seen many decent trannys go out right after a fluid and filter change. My buddy has a drain plug in his tranny and he drains about a quart a week and adds a fresh quart so he doesnt mess up his tranny by adding all...
  17. dcurtis

    What welding rods for sub-frame connector install?

    The only close muffler shop around me still uses a torch and a rod to weld:shrug: but I do have 4 ramps and 4 jack stands to put the car on, I'm gonna install them in my basement/garage, it is perfectly level:nice:
  18. dcurtis

    What welding rods for sub-frame connector install?

    I guess the mig welder route does make more sense, plus it will give me the excuse to finally buy my own.
  19. dcurtis

    What welding rods for sub-frame connector install?

    I was thinking about using one of those hobart 125 ez welders, but I heard that the stick welder would get a stronger weld. Would that mig welder do fine.
  20. dcurtis

    What welding rods for sub-frame connector install?

    Going to be installing sfc's some time soon, I have a 220amp lincoln arc welder and was wondering what welding rods you have used or what you would recommend for the job?
Top Bottom
Back
Forums
Menu