Search results

  1. Takt

    Dual Quad Carb Tuning

    I've got a dual quad carb setup on my mustang. It is two holley carbs (390) on a high rise manifold. I've had both carbs rebuilt by a guy that knows his stuff. Before I take the car back to him, thought I was get opinions from this site. When I get on the gas pretty hard, I have a severe...
  2. Takt

    Very soft pedal after frong disc brake swap

    Two weeks ago, I used the swap kit from discbrakeswap.com. Everything went smooth, and would recommend. However, I have a very soft pedal ... goes all the way to the floor before I stop. THe pedal does not pump up ... so no air in the lines. Everything is hooked up correctly and I bench...
  3. Takt

    to all the Vets out there, Thanks you for your service and have a nice veterans day

    I love this passage... WHAT IS A VET Some veterans bear visible signs of their service: a missing limb, a jagged scar, a certain look in the eye. Others may carry the evidence inside them: a pin holding a bone together, a piece of shrapnel in the leg - or perhaps another sort of inner...
  4. Takt

    2.8 ratio - 8" Open Center Section

    Here are a couple pictures
  5. Takt

    2.8 ratio - 8" Open Center Section

    I just pulled this out of my 1966 mustang. Good Condition. It has a tag with it. No problems when I was running it, just decided to go with a posi rear-end. Center Section 2.8 open 8 inch $85 plus shipping. I ship using FedEx ground. Will accept PayPal or Money Orders. If using a...
  6. Takt

    C4 Transmission -- I think I screwed the pouch

    So we're talking about going away from the C4 to a different transmission. Or is there an "add-on" that gives the C4 an overdrive? If a different transmission, which one? Thanks
  7. Takt

    C4 Transmission -- I think I screwed the pouch

    I think it was leaking at one of the hose connections (to run the fluid to cool it). I didn't get that far :) AOD -- you are speaking greek to me. What is entailed on making that conversion? I'm not worried about the drive shaft or anything, but not sure what you are talking about. Thanks,
  8. Takt

    C4 Transmission -- I think I screwed the pouch

    I have a 66 Mustang with a 302, 2.8 open gears and a C4 Transmisison. I had/have what I thought is a small leak of tranny fluid. I drove the car about 75 miles and it did fine. When I got home, I checked the fluid -- and it was bone dry. I filled it back up, but couldn't go for a drive until...
  9. Takt

    Dual Quad Intake Need help with Adjustments

    Spoofty, I thought the hesitation was due to too much fuel being dumped into the cylinders .. but per your post, I'm wrong? I am going to take my car to the carb guy to have him help me tune. He lives in Illinois, I live in Wisconsin, so I thought I'd try it myself.... try to learn a little...
  10. Takt

    Dual Quad Intake Need help with Adjustments

    Yes, he had all the specs. He called Holley to get their opinions as well. Everyone thought this would be a good application for my car. I don't know what progressive throttle linkage is. I'm sure I don't have it though. I'm attaching a picture of the linkage (well before I cleaned...
  11. Takt

    Dual Quad Intake Need help with Adjustments

    The basics – I have a 302, with a slightly aggressive cam, Pertronix Ignitor pointless conversion with flame throw coil (45,000 volt). I have a dual quad carb setup with high rise manifold and two Holley 4 barrel 390 cfm carbs (model 4160). The car has a C-4 Automatic and currently a 2.8...
  12. Takt

    65/68 Rear Frame Rail Passenger Side Complete

    Complete Rail sold -- Other two still available.
  13. Takt

    65/68 Rear Frame Rail Passenger Side Complete

    Prices lowered. Everything negotiable.
  14. Takt

    65/68 Rear Frame Rail Passenger Side Complete

    More Pictures. Email me if you need/want more. This shorter rail is 38" long -- driver side.
  15. Takt

    65/68 Rear Frame Rail Passenger Side Complete

    I have a complete Passenger Side Frame Rail -- never installed. Looking for $150/OBO plus shipping. - SOLD I have the drivers side frame rail -- back end. I installed/fitted the torque box back through the hump. I'll get measurements and update the listing. Looking for $40/OBO plus...
  16. Takt

    Holley Carb Idle Question

    Thank you very much. I've located the secondary vacuum assembly in the instructions. This will help a ton. Thank you!
  17. Takt

    Holley Carb Idle Question

    I have a 66 mustang with a 302 bored over, with a high rise manifold and dual quads on it. The carbs are Holley 4160 390cfm. I can't get it to idle below 1,100. It fast idles over 2,200. I screwed around with it for awhile, unhook all the linkage, reset everything, and the primary idle...
  18. Takt

    Post Your Stang!

    How about now?
  19. Takt

    Post Your Stang!

    Not as pretty as most, but different -- and I like it :D EDIT: - I was trying to embed them -- must not have worked?
  20. Takt

    Opinion Please -- Contemplating a rear end swap

    Thanks guys -- Sorry, I thought I posted that I have a 66 mustang, obviously didn't. The shorter driveshaft is exactly the type of thing I wanted to know. To upgrade to disc fronts -- I'd need the front kit, but also a new MC and a booster, correct? Thank you for the response. I'm...
Top Bottom
Back
Forums
Menu