Search results

  1. 0

    3/8 vacuum check valve. Please recommend

    Hey guys, Awhile back one of you posted a link to an aluminum vacuum check valve that cost around $30. Unfortunately I have lost the link. So if anyone knows of a good 3/8 check valve that I can splice into my heater control vacuum source I would really appreciate it. I have to stop the...
  2. 0

    Swapping to an auto trans from manual

    Hey guys. My horse power is far surpassing the limits of my stock 5 speed. So since I am planning on making this an agressive street/strip car I was thinking about going with an automatic trans. Is this possible to switch from a stick shift to an auto? If so what are your recommendations for...
  3. 0

    misfires on turbo and vaccum leak help!!

    Hey guys. I have been having trouble with my turbo 4.6 running 16psi . everytime am wot i get a misfire code. thus far i have pulled po306 and po302.Not sure what to do about this. Also i have my climate control vaccum source hooked up to the stock location. So it is seeing vaccuum and boost...
  4. 0

    turbo stang dies after spinning tires

    hey guys, every time i burn through first and second gear my car hesitates and shakes after i let off the throttle. It did it tonight and when i went to go shift third while buring through second gear the car totaly lost all power when i mashed on it in third. The car doesnt die out under hard...
  5. 0

    intake manifold and tb combo on turbo stang

    hey guys, i am looking for some advice on what throttle body and plenum to use. my set up is an mmr900 short block with pi heads with a single 60mm turbonetics turbo. this winter i plan on getting the edelbrock victor jr intake. i want to get the edelbrok intake elbow as well. my problem is...
  6. 0

    pi cams in t bird

    I have a set of pi cams with 55k on them. I wanted to sell them to my friend who has a 4.6 t bird. will they fit?
  7. 0

    wheel alignment after k member install

    Hey guys, I put a qa1 k member and coil overs in my 2002 mustang gt. i know i need a wheel alignment. when i called the shop to make an appointment the guy asked me if qa1 had any special line up specs or if it was to be lined up to stock specs. are there special line up specs or do they just...
  8. 0

    lift points on 2v 4.6

    Hey guys. I need to lift my engine up off the k member becuase i am replacing the oil pan with a mmr 7 qt unit and swapping out the k member with the qa1 kit. i was just wondering where the factory/best lift points were on the motor because i am going to have to support it with a cherry...
  9. 0

    Which Turbo?

    Hey guys. I am converting to a single turbo set up on my 2002 gt. I used to have an allen blower but the system isnt great for much over 350 rwhp. I am aiming to produce roughly 400-420 horse at 10psi but no more due to stock motor. (i understand forged internals are a must at some point) I am...
  10. 0

    missing shifts. clutch adjustment?

    I have trouble making the car go into the gears under heavy load (drag track) is this a symptom of my clutch being out of adjustment or something more serious. I just installed the clutch adjuster kit from Americanmuscle.com. this kit included a firewall adjuster, quadrant, and adjustable cable...
  11. 0

    tach very innacurate.

    i just installed my summit racing digital tach and it is very innacurate. it seems to say my engine is only ideling at 100 rpm and it doesnt get any better as the rpms increase. i spliced into the last coil pack on the driver side for a signal input. does anyone know why the tach is so far off...
  12. 0

    shift light signal wire

    hey guys i know this is probably an old question but i couldnt find it in the search. What is the best place to attach the green signal wire from the shift light to a 2002 gt. ive heard negative side of number one coil pack but ive also heard there is a wire going to the computer. please let me...
  13. 0

    forged or billet steel flywheel?

    i was researching which flywheel to get as i am replacing my clutch with the fidanza 2.1 kit. i noticed that fidanza makes a forged flywheel that is roughly the same cost as the ram billet flywheel. which one is better? they are both available on american muscle. and also would i gain a lot by...
  14. 0

    50 shot on blown motor

    hey guys, i have an 02 gt with 8 psi putting 320 to the rear wheels. my question is this; will a 50 wet shot of nitrous kil the motor or will it remain reliable? the motor is stock, but will have a nitrous tune. any help would be greatly appreciated. thanks.
  15. 0

    cd performance?

    does anyone know if cd performance in fall river ma is still open? i guess they are a dyno shop that specializes in mustangs. I tried calling but the line was disconnected. just wondering if anyone knows if they are still in business. thanks
Top Bottom
Back
Forums
Menu