Search results

  1. B

    Mustang Parts

    Looking to sell whole motor.
  2. B

    Mustang Parts

    At this point I can do either.
  3. B

    Mustang 4.6 Engine & Transmission

    This is what this COMPLETE engine has; after market BBK 78mm throttle body with plenum, 30lb. injectors, Comp cams 268 extreme cams, Comp cams valve springs, seats and new valve seals. The block is from a 98 stang with 50K miles and the heads are PI giving the motor 10:1 compression. Also...
  4. B

    Mustang Parts

    1998 Ford Mustang Gt with front end damage good for parts. Motor has PI heads with compcams. and valve springs 10:1 Compression...engine work done 6 months ago, X-pipe with high flow cats and magnaflow cat-back. Tremac 3650 5 speed trans steeda shifter and 373 gears. Late model 04 Cobra brakes...
  5. B

    Mustang Parts

    1998 Ford Mustang Gt with front end damage good for parts. Motor has PI heads with compcams. and valve springs 10:1 Compression...motor done less than a year ago...X-pipe with high flow cats and magnaflow cat-back. Tremac 3650 5 speed trans steeda shifter and 373 gears. Late model 04 Cobra...
  6. B

    headgaskets will not seat right

    Do you have the dowels in place...sure you have the right gaskets...are you torquing the heads correctly?
  7. B

    need more 2v power please

    Guy on ebay selling a blower kit for $1800.00
  8. B

    Cam selection / AFM's N-41

    Just a reminder. If you're NA now and SC later on the 2031 will work for both. I've been doing this for 20 years and have had plenty of experience and changed the cam on the recommendation of a well known dyno shop. Read up on the 2031. It's a great street cam and cheaper than the AFM. Any way...
  9. B

    Airbag Question

    The connector has 3 holes in it with 3 wires going to it...one wire on each end with a ground wire in the center.
  10. B

    Cam selection / AFM's N-41

    The AFM cam for 1.7 rockers is the B-21. I installed that cam thinking it would make a difference but I guess I already had reached maximum cylinder flow with the 2031 and a larger cam did nothing. The AFM has a better exhaust note to it. I'm running Holley System Max with Edelbrock heads and...
  11. B

    Cam selection / AFM's N-41

    Go with the Crane 2031. It's made to be used with the 1.7 rockers and is good for na & sc engines. I used it for years and I'm sorry I took it out. I replaced it with a AFM and it made no difference in hp. I have every mod you could imagine to a 5.0 on my engine...trust me.
  12. B

    Airbag Question

    Thanks for the advice. The plug that goes into the steering colume has 3 pins on it...short out all 3?
  13. B

    Airbag Question

    I have a 90 Mustang. The airbag light is flashing 6 times, pauses and flashes 6 times etc. I read that the clock spring is the cause and replaced it. This did not correct the problem. Anyone know what else could be causing this?
  14. B

    Timing Chain Cover

    Does anyone know if a timing chain cover from a 98gt will fit a 2001?
  15. B

    98 gt fuel pump

    Does anyone know how many lph the stock fuel pump flows?
  16. B

    PI Cams and PI intake Manifold

    You can get the FMS performance intake made for your car with all the parts you'll need on ebay for $285.00. You can pick new cams up on ebay for around $50.00. People swap these cams out of the pi heads for the crane or comp cams. Depending on mileage you should change your valve springs being...
  17. B

    PI Non PI Specs.

    Thanks for the reply!
  18. B

    PI Non PI Specs.

    Does anyone know the specs. on the pi and non pi cams? I heard the pi cams have more lift but less duration. If this is true wouldn't the non pi be better for mid and top end performance?
  19. B

    PI Intake

    I have seen a complete kit for $289.00. Do you think I'm better of going with that?
  20. B

    PI Intake

    I know this is an old subject but I'm reading many different opinions. Can someone please tell me what I would need to install a pi intake on a non pi motor besides RTV silicone gasket and intake?
Top Bottom
Back
Forums
Menu