Search results

  1. zm830101

    '66 cowl restoration

    well, got started on the cowl restoration on my coupe. been a long time coming and i am finally getting around to it. i was hoping that it would be a simple patch of the lower panels but it looks like that is no longer an option. while grinding on the spot welds i noticed this. it...
  2. zm830101

    Mustang Drop Spindles

    whatever became of this little endeavor?
  3. zm830101

    Show me your custom steering wheel . . .

    the lecarra doesn't have much dish, but the adapter is about 5 inches tall. also, for what it is worth, after about ten years, mine looks like hell. the varnish has peeled in places and the wood is chipping. pretty disappointing considering how much i payed for it.
  4. zm830101

    5.0 conversion questions

    all these solutions to the dipstick hole are killin' me. do it right. do it once. tap it for a pipe plug and never worry about it again.
  5. zm830101

    heater coolant tubes

    perfect! that is what i was looking for 2+2. i had seen the ones for the boss 302 but i had been unsuccessful in locating a picture of the one for the cleveland.
  6. zm830101

    heater coolant tubes

    got a picture?
  7. zm830101

    heater coolant tubes

    yeah, i have looked at the HD too. they sell a copper pipe adapter that you can braze to copper tubing that gives you a 1/2 inch female pipe thread. then you could screw in a 1/2 in brass fitting with a 5/8 barb so that you could connect your hoses. but now your talking about a LOT of potential...
  8. zm830101

    heater coolant tubes

    anybody ever tried to make some hard lines for their heater hoses? similar to what the fox bodies used? got any pics?
  9. zm830101

    going to attemp to redo my seats

    thin plastic? like maybe some 4 mil vinyl sheeting from lows or something similar? that's actually a good one. i had never seen that one posted before. thanks for the tips guys. keep 'em coming.
  10. zm830101

    going to attemp to redo my seats

    so i went to mustangs unlimited today and got some new seat buns and i already had the upholstery. i have the day off tomorrow so i think i will try to re-upholster my driver seat. anybody have any tips or tricks?
  11. zm830101

    Good place for a mini starter?

    why are you trying to wire it to the switch? all you need to mess with is the solenoid. pictures post # 4 is your friend
  12. zm830101

    Good place for a mini starter?

    well, i can't take credit for that list. but it isn't rocket science. add the cougars to it...but look carefully before you start wrenchin'. they were hit or miss. also, the e and f series HAVE to be an auto trans.
  13. zm830101

    Good place for a mini starter?

    i used to have a list of all the vehicles that you can grab these out of. i'll try to dig it up.
  14. zm830101

    Good place for a mini starter?

    a thunderbird with a 3.8 if i remember correctly. you do realize that ford used the exact same starter in NEARLY all of their rear drive platforms from the early to late nineties right? from mustangs to the e series van...they are mostly the same.
  15. zm830101

    Good place for a mini starter?

    i got mine from the local pull a part...$18 and works great
  16. zm830101

    front suspension binding?

    ca anybody else elaborate on the toe in issue or knows what to make of the alignmet numbers i posted previously?
  17. zm830101

    front suspension binding?

    measurements from the alignment shop left right camber .11 .09 caster .46 .94 toe .24 .24 cross camber .02 cross caster -.48 total toe ..48 the guy aligning it took roughly two hours to get it to this point. do...
  18. zm830101

    front suspension binding?

    my 66 coupe does something weird when i pull in the driveway and park. the suspension stays extended until i move the wheel back and forth a couple of time and then it settles out. i'm talkin like 3 to 4 inches extended! it looks like it is a lifted 4x4 or something. car is fresh from the...
  19. zm830101

    Quick auto to manual question (tried search)

    my steeda tri ax fit without cutting in my 66. BUT, the front bolt holes were covered so i decided to trim them up so the shifter could be removed without dropping the trans.
  20. zm830101

    Dipstick for T5? Stop leak?

    changing from synthetic to conventional won't do you any bit of good. go to a local parts store and ask for one of the hand operated pumps that attaches to the top of gallon and quart sized bottles. it will make your life A LOT easier when you fill it. aside from that, biting the bullet and...
Top Bottom
Back
Forums
Menu