Search results

  1. C

    What Flywheel?

    Yes, it's stock. Thanks. Is there any benefit in a Steel Billet vs Iron?
  2. C

    What Flywheel?

    There's vibration coming thru my shifter at 3200+ rpm. I think it could be my flywheel. Can I figure out what flywheel I need without taking it out first?
  3. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    Update on Magnaflow X-pipe w/cats Well, I went with the Magnaflow X w/cats. And I must say that I do like the sound. However, I did have have fitment problems. It was not wide enough and the end was too small to fit properly over the header flange. I called Performance Peddler. They...
  4. C

    Buzzing when under a load???

    The spacer did the trick! No more problems at 70 & above. Still having the noises as I slow down from 50 mph in 4th. But I really think that this is a design issue.
  5. C

    Do MAF and injectors have to match?

    Thanks. That saves me time and money.
  6. C

    Do MAF and injectors have to match?

    Thanks guys. I guess I could send my Pro-M off to get recalibrated. I just didn't want to take on that additional time or expense. Maybe I'll just wait until I a turbo kit. However, that does bring up another question. I already have a E303 cam, 70 mm throttle body, pulleys, cold air...
  7. C

    Do MAF and injectors have to match?

    I am about to put some Victor Jr. heads on my '95 Stang. I am thinking replacing my stock 19 lbs. injectors with 36 lbs ones (I hope to turbo someday). I have just been told that I could upgrade my injectors without upgrading the MAF. I just would not see the benefit until I upgrade the...
  8. C

    Distance btw T5 yoke and floorboard of SN95?

    I have a Tremec 3550 in a SN95. It buzzs loudly in 5th gear above 70 mph and at 55 mph in 4th. I been told that the driveshaft angle is different due to the length of the the 3550 compared to the T5. This affects how far the drive shaft inputs into the tranny. I plan to install a spacer kit...
  9. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    Brent, Thanks. Is it true that the bar between the pipes is for connecting to the tranny mount? I have a SN95 GT with a Tremec 3550.
  10. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    Thanks. I'm leaning toward the Magnaflow because: 1. Magnaflow X-pipe has a bar between the two pipes that I read could be connected to the tranny mount to eliminate knocking 2. Magnaflow has the hangar hardware (UPR doesn't) 3. I have magnaflow mufflers and I love 'em. 4. and even...
  11. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    Is the fitment problem more with the Fox body or does it also affect the SN95?
  12. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    Great! I'm found a very good deal @ Performance Peddlers. Also, I read somewhere the UPR sometimes rubs the tranny under aggressive use. Has anybody else experienced this?
  13. C

    Which to choose? UPR or Magnaflow x-pipe w/cats

    I need new cats for my '95 GT. I'm debating between the Magnaflow X-pipe w/cats and the UPR x-pipe w/cats. UPR has high flow Cats and supposedly better clearance (which I need since my car is lowered). Will they pass the 'sniff test"? Magnaflow is stainless steel (I think?) and should last...
  14. C

    urp catted X

    Did you ever buy the UPR x-pipe with cats? Reject5.O, did you ever buy the UPR x-pipe with cats. If so, how do you like them. I thinking about buying them, also. Or maybe Magnaflow.
  15. C

    Tri-Ax vs. UPR Bluethunder

    I have a '91 LX with a T5 and a Bluethunder. I love the way it shifts. I have a '95 GT with a Tremec 3550 and a Tri-Axe. I hate the way it shifts. Maybe the difference is more because of the tranny or installation??:shrug: Before I bought either shifter, I always thought that the Tri-Ax...
  16. C

    Buzzing when under a load???

    Thanks for the all the info. I going to try the 3/8 space on the driveshaft and the washer under the tail of tranny. I think I already have a nylon washer in shifter but I'll check that also. I made a few more calls and one guy thought that it could be the input shaft. Sounds pricey and...
  17. C

    Buzzing when under a load???

    Thanks 88Stangboy for the info. At least I can worry less about it breaking. I did get an email today that told me that I should pull the tranny and check the shims. Now, the guy who rebuilt it last year told me that he packed it as tight as possible. Is it possible to pack it 'too...
  18. C

    Buzzing when under a load???

    Wow! It's good to know that I'm not alone with this problem. Honestly, I'm at my wits end on this one. I taken to couple of drivetrain guys. Both says it's the transmission's design and nothing can be done to fix it. I'll have to live with it or replace it. However, neither is sure...
  19. C

    Buzzing when under a load???

    I have a 95 mustang GT that was converted (by a previous owner) from an automatic to a manual. The tranny, a Tremec 3550, was rebuilt last year. Also installed was a new transmission mount, the clutch and short-throw shifter. The problem is that under load (above 2800 rpm), there is a...
  20. C

    Overheating: How do I check a radiator fan and sending unit?

    Thanks for that info. I've had some recall work done (the hood and the parking brake, which got worse after they fixed it) but not the fan. I'll check on that.
Top Bottom
Back
Forums
Menu