Search results

  1. B

    351 shorty headers

    I haven't seen any 1 3/4" swap shorty headers either.
  2. B

    351 shorty headers

    By who?
  3. B

    351 shorty headers

    I'm aware that the 351 sits in the same location as 302. I was just wondering in your particular application did you use an aftermarket K-member that maybe lowered the motor or set it back to get the headers to connect to factory 302 midpipe. So do the headers have to be labeled "swap...
  4. B

    351 shorty headers

    Yes I did mean for Windsor. What headers are they and does the standard H-pipe work with no problems? Also is the location of the motor still stock?
  5. B

    351 shorty headers

    Anyone using shorty headers on a 351?
  6. B

    Blower Motor..short stroke or longer stroke??

    Boost about 10-12psi and I was going to try to use shelf stock piston.
  7. B

    Blower Motor..short stroke or longer stroke??

    I'm sorry I got a little confused. What I meant was would it be better have a 3.85 stroke vs. a 4.00 stroke using a 6.2" rod? Or would it not really matter?
  8. B

    Blower Motor..short stroke or longer stroke??

    Looking into 351 based centrifugal blower motor for the street and was wondering if it would be better to have a longer stroke (6.2" rod) or shorter stroke 5.4" rod. Would like to shift at 6500 with hydraulic roller.
  9. B

    Blower street motor question

    I am planning on using a Dart block. How much boost is your tuner running and is he using a hyd. roller?
  10. B

    Blower street motor question

    302 based block....not just a 302. Obviously need some stroke to get the number
  11. B

    Blower street motor question

    What would be the better choice for displacement and/or stroke for a street driven centrifugal blower motor? I was thinking of a 351 based block and stroke to a 427 but I think I may have read somewhere that it would be best to go with a shorter rod length than 6.2 Or maybe stay with a 302...
  12. B

    Issue with DCC FK35

    I want the whole loom. Thanks
  13. B

    Issue with DCC FK35

    Baskin, I'd like to use your wiring. How much would it be for me to get part # WL-10? And how soon can I get it? Thanks
  14. B

    Issue with DCC FK35

    Well I am most likely going to opt to go the fuse route using the maxi fuse and inline holder. The inline holders use an 8 awg wire so I will need that size butt connector. I will fold the stripped end over of the 10 awg wire supplied in your kit to make a snug connection in the 8awg butt connector.
  15. B

    Issue with DCC FK35

    You mean the butt connectors? I appreciate the offer but I can get them. Anything special about them other than a standard butt connector from the store?
  16. B

    Issue with DCC FK35

    btw...is this the recommended type of crimper http://www.partsexpress.com/pe/showdetl.cfm?&DID=7&Partnumber=360-642
  17. B

    Issue with DCC FK35

    Thank you very much
  18. B

    Issue with DCC FK35

    Baskin, I appreciate your info and comparison. I am not to trying to give you a hard time or anything of that nature, just trying to understand. Reason I wanted to move away from the fusible link is that when the link melted it almost ruined some wiring next to it. Only thing that help prevent...
  19. B

    Issue with DCC FK35

    I am looking at the page but I don't see the comparable fuse size for 14awg fusible link
  20. B

    Issue with DCC FK35

    So the FK35 kit does come with 10awg power wire, correct?
Top Bottom
Back
Forums
Menu