Search results

  1. I

    vibration @ 2300-2500 in EVERY gear except Neutral??

    u-joints, driveshaft balance, tranny mounts, engine mounts coming loose a bit?
  2. I

    ever seen pink spark plugs??????

    Never seen a pink plug, I assume Barbies vette might have em but.....as far as fprs, mine is not connected to my computer and while the computer sends a signal to the fuel pump to turn on, thats as far as it goes as far as I know. Think of one as a valve that you can adjust the threshold of...
  3. I

    HUGE Problem!!! Need help.

    Oh that really sucks, been there a time or two, take head off and take it to a machine shop and have them drill it and rethread it, ez outs are made of VERY hard metal. Buy better bolts for valve covers next time, no major torque there they should not snap...sorry for your luck, mine was a...
  4. I

    A little help needed

    bumpity bump
  5. I

    harmonic balencer

    Usually they spin, the outer part turns a bit from the inner and it becomes impossible to set your timing well as the marks are off, plus you never know what you may break if your engine is shaking too much....engine mounts...premature bearing failure etc etc...not worth running with imho, I...
  6. I

    A little help needed

    Hey all, finally got my act together and finished off the engine/tranny re-install and got it running again, runs great/sounds great/looks great, must be a Mustang...anyway I'm now ready to put some decent rubber on it, it is an 88 GT with a full Saleen body kit and 16 inch Saleen rims with...
  7. I

    Dizzy & Timing Issues (30*????)

    What I did was to stick my finger as far in the #1 spark plug hole as I could(if you have small fingers don't get carried away here) with one hand, and cranked the engine over BY HAND with a large socket until I felt my finger was getting pushed out of the hole by air pressure, I put a pencil in...
  8. I

    Engine goes down, timing chain... Replacement engine or easy fix?

    1300? You should be able to rebuild the entire motor for that much, I found a nice set of heads for 500, and did the rest of the motor for 1000 but I did everything....try a different garage?
  9. I

    2 problems, no vroom, help needed!

    Thats a good idea 86bluecobra, possible I should disconnect and remove the short tube headers as well...
  10. I

    2 problems, no vroom, help needed!

    I am running 24s but as I paid good money for these rails, I hoped to use them, they are I think professional products 5.0 rails, I got them at a local shop, they are like these, http://cgi.ebay.com/ebaymotors/10600-Professional-Products-Fuel-Rails_W0QQitemZ260058491874QQcmdZViewItem I did...
  11. I

    2 problems, no vroom, help needed!

    I'll try not to write a book here...basically I totally redid my mustang, total engine redo, total transmission redo etc etc, 1988 GT, 306, T-5,Centerforce DF, world heads, cobra upper/lower, e-cam, msd 6al, headers, h-pipe etc etc, it is almost together, origiannly the factory fuel rails were...
  12. I

    plugging smog holes..

    plugs I got mine at napa, they were called thermactor plugs, threaded plug that has screws outside and in, sealed it with thread sealer with teflon. If I ever get this engine and transmission in I'll let you know how they work but that is what they are meant for.
  13. I

    Head bolt size?!?!?

    bolts 2 and 5/8 and 4 and a 1/4 if I remember correctly, buy arps.....
  14. I

    push rod length??

    get one pushrod checker, your new friend, basically an adjustable pushrod that gives you an exact answer as to how long they should be. @20 bucks and worth it.
  15. I

    Low mile 1996 351W cam question??

    well I guess more info is needed, what are your plans for the car? The fact that you are putting a 351 in place of the 302 suggests you want more performance. If thats the case, now is the easiest time to do cam/heads swap.
  16. I

    5.0hh no misfiring :(

    really? I was not aware you had to have #1 cylinder at tdc to install new heads...
  17. I

    Accessory help

    bump
  18. I

    Accessory help

    bump hoping for a schematic/picture...
  19. I

    Accessory help

    Hi everyone, I could use some help assembling my rebuilt motor, I did not take pictures when I took it apart(lost camera battery) and after many delays, I cannot remember how to put the front of the motor back together. Bolts/studs/nuts/spacers/etc Anyone have a diagram of which bolt/stud goes...
  20. I

    dash help

    bump
Top Bottom
Back
Forums
Menu