Search results

  1. muddslide

    My new 347 powered by a 671!!!

    The car has a 2,800-3,000 stall, I don't think it will break the tires too loose. I have a problem with all that hp in first gear, so I might try short shifting into second gear... This might kill my 60' times.
  2. muddslide

    My new 347 powered by a 671!!!

    Has anyone used the two stage msd launch control box? I was briefly reading an article about the box controls your launch, so you can launch at a certain rpm and H.P. to allow traction and it controls you wheel spin. This way I can launch with a transbreak and not blow of my M/T drag radials.
  3. muddslide

    My new 347 powered by a 671!!!

    Yes, looking back on it the c6 would have been much easier. I had a racing 350 already in the garage, needless to say, they didn't hold the torque, so I broke two of them. I aready had the ultra-bell from J&W so I went with the 400. I like the combo but went through hell getting it. My over...
  4. muddslide

    My new 347 powered by a 671!!!

    I have been building this car fir 4 years, I just was able to drive it. The car gets looks, I hope to make a few more changes to get it it to the low 10's or high 9's.....
  5. muddslide

    My new 347 powered by a 671!!!

    I need to make a gear change, I have a 300 rear gear in it. I have two pullies, one is for 5psi, which makes the motor 1 to 1, so I can run it on pump gas. And the second makes 16-18psi and runs with 110 race fuel. I brought the car to the track and couldn't get any traction, my best time was...
  6. muddslide

    My new 347 powered by a 671!!!

    I have a bunch of pic's saved to snapfish, I'm just trying to figure out how to use them here without taking each pic from snapfish and saving them to my computer and then adding them here. I need a little bit, I'm not the computer guy......
  7. muddslide

    My new 347 powered by a 671!!!

    here is anther one, I will try to post a few with it in the car. I have changed a few things and hope to add a few new pics. I also have dyno results......
  8. muddslide

    My new 347 powered by a 671!!!

    Here are a few pics of my new 347 dart block with a 671 bds blower. What do you think?
  9. muddslide

    superchargers

    Well I just went with a 671 roots set up on my 347 dart block. I'm only running 6psi and it's sick on the street. I'm building it for 16psi and meth injection to cool the blower. There is nothing sicker than a stang with a hugh blower sticking out of the hood. I will try to post a few...
  10. muddslide

    3.00 gears revs 3000 at 70mphs?

    Yes that sounds correct. I also have the same gear and at 3,000 rpm I'm at 68-72mph. Hope this helps
  11. muddslide

    Another way to attach door panels?

    I used jb weld for plastic. I went around all the cracks and tairs with it and it made them super stong.
  12. muddslide

    65 mustang superchargers?

    I just built a 347 stroker, with a 671 blower. I used the Dart block and I'm hoping to dyno it soon. I have two pullies for the street and track. So far with only 6-7 pounds of boost, its scary. I have a drag car that runs in the low 10's and I think my stang would take it. I'll try to get...
  13. muddslide

    I broke my cobra r rim!!!!!

    Is there a difference between the 95 cobra r's and the 98's?
  14. muddslide

    I broke my cobra r rim!!!!!

    Thanks, it still said my pics are to big to be uplaoded.
  15. muddslide

    I broke my cobra r rim!!!!!

    It said my file is too big to upload, how do I resize it. On my camera it on the lowest setting.
  16. muddslide

    I broke my cobra r rim!!!!!

    I was driving home and hit a brick, it broke my front rim and I don't know what to do. I need to replace the rim but I need a cheap one. I'm poor right now so I don't want to spend a lot. These rims are real cobra r's but could I buy a fake one for now and where is the best place to get them...
  17. muddslide

    Installing Tach/Shift Light

    I seached the forum but couldn't find an answer. How hard is it to install a tach shift light on a 96 cobra. I know in my 2000gt I needed to bypass my computer. Do I need any special wire kits or do you just splice into my wiring system. Thanks for all the help.
  18. muddslide

    Motor mount q's

    Anyone with them on their stangs?
  19. muddslide

    Motor mount q's

    How much should i expect to pay for a good mount? I looked at the moroso web-site and they don't even sell a soild mount for early stangs. They start a 70's
  20. muddslide

    Motor mount q's

    I'm installing a dart 302 block in my 67 stang and want to go with solid motor mounts. I noticed they make different year motor mounts. I think they were 70-94. Do I need to get them for a 67 302, or will any 302 motor mounts work?
Top Bottom
Back
Forums
Menu