Search results

  1. 1Bad88notch

    FOR SALE 88 LX COUPE

    302 bored .30over. 5spd. Canfield heads port&polished, lunati custom cam, comp cams beehive springs 1.6 roller rockers, Edelbrock Victor JR. intake port matched to heads. JE flat top pistons, eagle connecting rods, 650 speed demon carb. melling high vol oil pump, Edelbrock high flow water pump...
  2. 1Bad88notch

    NEED HELP! or im selling it

    ok heres my problem, after my car gets warmed up it runs fine but if you shut it off and start it right back up it runs like crap sounds like its not running on all 8. if you let it sit for a few minutes it runs fine. i have a 650 speed demon on it and a crane cams ignition box and street/race...
  3. 1Bad88notch

    need help with carb

    I have a 650 speed demon on my car, the problem is that when i first start it up it doesnt want to run. it pops through the carb and you have to keep pedling it to keep it going. after it gets to operating temp it idles and runs fine, but if you let it sit for about an hour it does the...
  4. 1Bad88notch

    spark coming out the side of coil

    I have a msd blaster 3 coil on my car and it is shooting a spark out the negetive side of the tower and arching to the negetive post on the coil. i just put in a new msd 6al box because the old one died. it started doing this after i put the new box in didnt do it before with the old box. i...
  5. 1Bad88notch

    motor wont stay running

    My question is i just got my new motor in my car and started it up today it will run for a few minutes then it just shuts off. it has a carb on it i cracked the fuel line to make sure no air is in the line. once it shuts off you can start it right back then it does the same thing after a few...
  6. 1Bad88notch

    Spark Plugs for Canfield heads

    just curious if you guys know of a good set of plugs for canfield heads. Looking for a set for my heads. Thanks, Dan
  7. 1Bad88notch

    building new motor,what do you think it will run

    The car is a 88 notch 5pd with full int. no a/c, lakewood 90/10 in fronts 50/50 in rear, moroso drag springs and southside lowers. The motor is a 302 .30 over stock crank,eagle rods, JE pistons, Canfield 190s with stage 1 porting, custom grind lunati cam .565 lift 1.6 rr, victor jr. intake port...
  8. 1Bad88notch

    Question about canfield heads

    I am going to be getting a set of canfield heads and i need to know if i need a certain type headers for them because the exhaust ports are raised on the heads. I currently have a set of mac L/T headers. Let me know if you guys have any ideas let me know thanks.
  9. 1Bad88notch

    Intake Question

    I currently have a victor jr intake for my car and im thinking about switching it out. I am having the motor bored .30 over i have a FMS f-cam in it gt40 cast iron heads and a holley 700cfm carb. I have been told that the victor jr is to much. I was looking at the performer rpm or a performer...
  10. 1Bad88notch

    DSS pistons

    Im thinking about getting a 306 dss pro-x piston kit for my car and need an opinion. Are they a good choice or are they junk!
  11. 1Bad88notch

    Short block question

    I recently blew a head gasket and now have my engine torn apart and debating weather to have my block bored out or just to buy a short block. Does anybody have an idea about how much it would cost to have it bored with new rods and pistons. I'm also on a budget and not looking to go overboard...
  12. 1Bad88notch

    AFR 165cc or 185cc

    I have a 88 coupe with GT40 iron heads with FMS 1.6 roller rockers,FMS F-cam, and a holley 700 CFM DP. I am looking to get a set of AFR's and my question is which ones would be the best for my setup. If you guys have any ideas let me know. Thanks, Dan
Top Bottom
Back
Forums
Menu