Search results

  1. k00ksta

    Stroker Motor Timing Question

    Also note this is at about 1400-1600 RPM I am at 32* not a 700 RPM idle.
  2. k00ksta

    Engine Installing A 5.0 In A '96 Six Cylinder Body.

    Why would he need the computer if he is going carb'd setup?
  3. k00ksta

    Stroker Motor Timing Question

    I got a 331 Stroker motor in my car with TrickFlow twisted wedge Heads and Intake, E303 cam, 75mm TB, MSD 6AL, Autolite 3492 gapped at 0.052-0.054 (ford spec), ect ect .. I got some timing questions .. 1) Do we need to have the car OFF when pulling the SPOUT out before adding/removing timing...
  4. k00ksta

    Anderson Pms

    Anyone using a Anderson Ford PMS Engine Management System on their 94-95 Mustangs? Before I drop the cash in the bucket I am curious on how it compares to other solutions like Tweecer, Quarterhorse, Holley's PMS System, ect .. Any input would be appreciated thanks! :}
  5. k00ksta

    Setting Idle: Which Screw On This Tb Is Correct One To Use?

    I have a question as I am having issues right now with my setup when the car is warm. Basically I followed the same procedure linked above to set my Base Idle which for my cam I have it at 900 RPM's. I have brand new IAC/TPS and are tested perfect. Now when I first start my car and its COLD IDLE...
  6. k00ksta

    Electrical Dead Battery Any Suggestions

    I got a 331 stroker motor in my stang and this summer it appears the battery I bought in 2006 :hail: has finally died its reading 12.3 volts after charging for a few hours but after testing at advanced auto parts it seems the cranking amps were at 120cca so I guess it sulfated and garbage ...
  7. k00ksta

    Engine Valve Cover Vent Hose Necessary?

    un-metered air is always bad business from what I have seen. But maybe its not enough to cause issues.
  8. k00ksta

    Engine Gt40p Setup Won't Idle

    Or replace your TPS (throttle positioning sensor)
  9. k00ksta

    idle staying at 2000rpm?

    I see your running 24lb injectors have you gotten a calibrated MAF for that injector size?
  10. k00ksta

    Which gears to get?

    Run 3.73's and be done with it thats my 2 cents :) ..
  11. k00ksta

    Exhaust Egr / Ac Delete Questions

    Ya I guess I will have to leave the EGR for now until I can get this thing to Mike Post for a tune and have him delete that crap.
  12. k00ksta

    Exhaust Egr / Ac Delete Questions

    Excellent Kurt thanks for all the low down on what I need to do here!
  13. k00ksta

    Exhaust Egr / Ac Delete Questions

    Hey guys I am about to rip the AC and the Smog pump out of my car and do the belt re-routing pictured here .. Now what do I have to do with any of the AC Lines or anything with the Smog pump after I pull these out? I would love to yank out as much as possible as I will never use the AC and...
  14. k00ksta

    Suggestions on Fuel Pump for 331 Stroker Motor

    Fuel Preasure Regulator I still am rocking the stock fuel preasure regulator as well .. Should I replace that as well while I am doing the pump?
  15. k00ksta

    Suggestions on Fuel Pump for 331 Stroker Motor

    Awesome just wanted to make sure going with a large pump would not cause any issues (computer wise). Also sets me up so I dont have to touch it if I do choose to super charge it down the road. Thanks going with the Walbro. :flag:
  16. k00ksta

    Suggestions on Fuel Pump for 331 Stroker Motor

    What size (LPH) Fuel Pump do you guys suggest for a 331 Stroker Motor (Check sig for other mods) I have no plans at the moment for Supercharging, Turbo, ect. Have the tank out the car at the moment and figure since its literally the original from the factory its time to get it the hell out...
  17. k00ksta

    Converting to a Carb'd Setup

    Also anyone had decent luck with quarter horse? or have a used tweecer rt they wanna sell? :)
  18. k00ksta

    Converting to a Carb'd Setup

    What cam would you suggest? I am emissions exempt.
  19. k00ksta

    Converting to a Carb'd Setup

    Anyone converted there setup to a carb'd setup? I am getting so damn tired of the computer in my SN95 that I am about ready to pull the top half out the car and just go carb'd. Getting chip's burnt is a pain and its not a daily driver so anyone think its a dumb move and I should just continue to...
  20. k00ksta

    Dipstick Tube location

    Ya the autozone one is garbage. :nice:
Top Bottom
Back
Forums
Menu