Search results

  1. 97gtconv.

    swap questions

    I just noticed you live in Haven, I live in the Lake Wynonah. Class 01' I'm down in Houston, TX going to UTI. I wouldn't use your programmer. I have a Superchips 1725 and when I got in dynoed the A/F was not safe at all. As for what u need as in parts and knowledge with the swap contact...
  2. 97gtconv.

    Video of my Comp Cam XE270AH-13

    sounds good with the cams....what's your car idle at?
  3. 97gtconv.

    5.0 carb questions

    for the great info
  4. 97gtconv.

    5.0 carb questions

    the pickup tube is a cartech pickup tube. thanks
  5. 97gtconv.

    5.0 carb questions

    Thanks for the great info. He said for compression it's pretty high as where he can't run anything less than 93. He estimates 10:1 and higher. He says the GT40-P heads were milled but doesn't know how much was takin off. His carb is a Holley 650 SINGLE pumper. It won't idle less than 1K...
  6. 97gtconv.

    5.0 carb questions

    anybody have anything?
  7. 97gtconv.

    5.0 carb questions

    I'm asking some questions for my roomate and there's a couple q's that he would like to know. This is what he has... 1988 LX 5.0 306 with forged internals, gt40 heads w/bigger valves light port work, holley 4barrel 650 cfm, mallory ignition, holley blue pump, e303 cam, edlebrock rpm manifold...
  8. 97gtconv.

    TB installation help PLZ!!!

    on my granatelli 75mm throttle body the hole was pretty small... i could barely push it in. i used some pliers and that did job. no damage done
  9. 97gtconv.

    WHAT DO U THINK I'LL PUT DOWN??

    Well I blew my motor about a month ago and I bought stock 98 gt shortblock that has new bearings in it...only has 40k on it. My car is 1997 Mustang GT Convertible Automatic.....I'm doing the P.I. swap on it also. My current mods are MAC long-tubes, MAC h-pipe w/cats, MAC Flowpath Catback, BBK...
  10. 97gtconv.

    stupid brakes

    i put new rotors on (front and rear) and reused my rear pads (nice and flat and nothin wrong) i put new ones on the front... i greased up all the slide pins and the put some grease on the surface of the brake pad. i cleaned out the rubbers boots. my car has a dead battery but i got a jump...
  11. 97gtconv.

    brake problems

    i'll try to see if the bolt works and a copper washer. do you know of place that just sells the copper washer? autozone, o'reilly's, and every other place only sells them in a rebuild kit. i'm about to rip out my emergency brake cause it's so damn annoying....cables handle the whole...
  12. 97gtconv.

    brake problems

    My car is a 97 gt automatic vert with 4-wheel disc brakes. i have a leak in my right rear brake line... where i think it's called the bleeder screw screws down into the caliper. the brake fluid comes from underneath the brake line where the copper washer is, that seals the brake line to the...
  13. 97gtconv.

    How much does your Stang weigh?

    How much does your Stang weigh? what things have you done to lighten it? I have my 97gt convertible with a auto and i'm trying to figure out how much mine weighs. i took out my spare and jack.
  14. 97gtconv.

    official 4.6 liter Mustang photo thread

  15. 97gtconv.

    Strut/Shocks/Springs Questions

    i have wEibach Pro kit springs, there 1 1/2". those are what are on my 97 gtconv.
  16. 97gtconv.

    2V n/a makes 365rwhp and 411rwtq

    i think it's just nasty
  17. 97gtconv.

    brake questions

    the screw tightens but it comes from between the block and the caliper where the brass ring is. the screw tightens well but the block has some nicks in it. i think that's what it is. i don't have a camera.
  18. 97gtconv.

    brake questions

    i tried putting new brass washers on and it still leaks.
  19. 97gtconv.

    brake questions

    what would i have to replace? how do i get off the brake line that connects from the caliper to the main brake line?
  20. 97gtconv.

    brake questions

    i changed my calipers with stock ones and when i put them back on and bleed the system the fluid was leaking out of the right rear. wouldn't have noticed but i had a buddy doing the bleeder screw. it comes out at the bleeder screw. i looked at the bottom of the line the square block that the...
Top Bottom
Back
Forums
Menu