Search results

  1. O

    China Cobra Intake Woes!

    The China intake won't work with a Kenne Bell intake either. The top sits back about 1/4 further than a real cobra intake. Just enough to keep the belt from lining up. Just think how many people have pulled there hair and lost money trying to use these intakes. That's a shame
  2. O

    Basic air conditioning wiring question on a fox

    Hi, I pretty much know the basics from the fire wall out Is this right?: The 12 volt wire for the compressor comes out of the firewall and into a pressure switch (shuts it down if 134-a is low) then to a relay that sends the current to the magnetic clutch on the compressor. If that...
  3. O

    Rocker Stud Snapped!! What Roller Rockers In Photo

    No,, I think the valve needed to "Kiss" the piston. But it may not have damaged the valve. I have done over revs and bent push rods and not damaged the valves before. Please post after you do a compression check and let us know.
  4. O

    Will fuel injection still work if the distributor is unhooked?

    Hi, I'm going to be installing a supercharger with a carburetor and using a Mallory distributor. I would like to know if I can pull the original distributor out and install the Mallory, Set the timing then install the supercharger. Once the supercharger is installed the only way to...
  5. O

    Car is down for the count...

    $150 Bucks and maybe your wife will hesitate to use your mustang from now on? That's a good deal. Just kidding---sorry I could not help myself No one is hurt and the car needed fixed anyway $150 Bucks is a rip off but just have a cold one and let it go.
  6. O

    Brake booster conversion

    Ok, What about the assistants do they both assist the braking the same amount? I'm running SN-95 brakes all the way around so it would make sense to run a SN-95 booster. But from what I have seen the the posts it looks like the Cobra booster is easier to install. If they both the same thing I...
  7. O

    Brake booster conversion

    Yes I looked at the sticky's ,,, And it said that the SN-95 and the 93 cobra are both 205mm tamden. Does that mean they both have the same amount of Braking assistance? Can the mounting studs on the SN-95 booster be removed and replaced with nuts and bolts to make it easier to...
  8. O

    Engine build and ideas please

    Why not build a sort of "stock-ish" engine for dependable and driveability and just ad some boost? keep decent gas mileage and have plenty power. a kenne Bell would be nice and you can pick up a really nice used complete hit for around $2000
  9. O

    Do these look like 17's to you?

    17's on the front of a fox
  10. O

    brake conversion 2 to 3 conversion question

    Ok I didn't know that,,, what does the shuttel valve part do?
  11. O

    brake conversion 2 to 3 conversion question

    As I set here and look at my post I ask myself, "Why even run the factory proportioning valve?" if you are going to gut it anyway why use it? Rear brakes-- The line would run out of the master cylinder into a willwood adjustable proportioning and then to the rear wheels. Front...
  12. O

    brake conversion 2 to 3 conversion question

    Hi, When doing a 5 lug conversion instead of using the 2-3 kit couldn't I just use a line lock? Gut the proportion valve and come out of the valve into a line lock and then two lines out of the line lock the front wheels? And run the adjustable valve for the rear brakes? I was...
  13. O

    Speedo Question? What would you do???

    If you look on eBay sometimes you will see just the 140 speedo by it's self. Some of the guys on eBay selling mustang parts make a living doing it. If you send them a message and tell them your looking for just the 140 speedo and not the whole cluster they can set you cheap. I payed $25...
  14. O

    tick....tick....tick....

    No I just put new pads on the rear LOL I have a booster and master cylinder jusy haven't got to it yet.
  15. O

    tick....tick....tick....

    When you go to rear disc you will want to change that master cylinder.---trust me on this. I switched my fox over to SN-95 disc all the way around and I didn't touch anything under the hood the pedal felt fine and the car braked well. --never changed the booster or master cylinder. Now a...
  16. O

    Slotted & drilled Rotors for 89 Lx drag car. Are they worth it?

    You said you are still running a stock 89 brake set up? was this originally a V-8 or 4 cylinder car? 4 cylinder has smaller brakes I know you don't want to hear about needing new wheels but if you did the 5 lug conversion using 94-95 mustang spindles the better rotors calipers should...
  17. O

    87-89 fox speedometer in a 91 cluster? 180 MPH

    I picked this up today I don't know why I wanted it I guess I thought it was cool. It's for a 87-89 but I think somewhere I saw a thread that said you could trim the face down and put it in a 90-93 cluster I'm thinking about giving it a shot. Is this cool or what? Anybody ever done...
  18. O

    87-89 speedometer in a 90-93 what needs to be done to make it fit?

    Oh,,, I can just trim the face to fit? I thought I saw that some where but I wasn't sure.
  19. O

    alternator 3-G upgrade question

    I been looking through the post and can't seam to find and answer for this one. I have a 1991 Fox and I was going to go with a one wire alternator. will the gauge in the dash still work? To me it looks more like a volt gauge that an Amp Gauge I'm asking a lot of questions when the...
  20. O

    2003 - 2004 shaker hood scoop modified to fit 87-93 fox?

    nice
View older results
Top Bottom
Back
Forums
Menu