Search results

  1. P

    estimate my horsepower/torque

    so, should it compliment the stroker kit, or hold it back? down the road i will most likely go custom cam and some type of aftermarket heads.
  2. P

    estimate my horsepower/torque

    with the correct cobra rockers (crane 1.7) it is .480 int and exh 118 deg lobe sep. and 270/270 adv. duration so pretty mild but a little more than stock ho cam. :rolleyes:
  3. P

    estimate my horsepower/torque

    its just a stock cam from a 93 cobra. my initial goal will be to run 12's with a very stock looking/stock sounding engine. then later add heads and a bigger cam :D
  4. P

    estimate my horsepower/torque

    what do you guys think this combo is capable of with a good dyno tune? 331 engine 10.2 compression gt40 irons heads, ported and polished. cobra cam 1.7 roller rockers ported/polished explorer upper/lower 70mm t/b and egr spacer 24lb injectors 70mm cobra maf long tube headers 190lph...
  5. P

    will stock valve covers clear cobra 1.7 rockers?

  6. P

    will stock valve covers clear cobra 1.7 rockers?

    did you have to remove just the baffle or did you have to grind the baffle mount webbing away also. i am only running a cobra cam so should be similar to your setup.
  7. P

    will stock valve covers clear cobra 1.7 rockers?

    i'm wondering if anyone has tried the stock cobra crane 1.7 rr's under factory 5.0 aluminum valve covers? i will be running the stock cobra cam as well. thanks
  8. P

    How much lift can stock gt40 heads/springs handle?

    these are gt40 heads, not gt40p heads. and vinnietbird, how much for the tf springs?
  9. P

    How much lift can stock gt40 heads/springs handle?

    ok, not sure i understand. the stock e7 heads/cam had less lift than the cobra cam w/1.7 rockers, right? but you are saying the e7 springs are better? if the gt40 springs wont work i'll get some trick flows but i was just wondering how much lift they will accomodate. i run an x303 with my...
  10. P

    How much lift can stock gt40 heads/springs handle?

    just wondering how much lift before coil bind on stock gt40 valvetrain. thanks
  11. P

    cam suggestions for 331

    i'm in bakersfield, north of l.a.
  12. P

    cam suggestions for 331

    help me select a cam for my 331. 10.2 to 1 compression, 93lx mustang 5 speed 3.73 gears, gt40 mildly ported, explorer upper/lower, i want this to be a street driven car that sees the track maybe 15 times a year. i also have to pass ca emissions. i have some crane cobra 1.7 rr's i can use, or i...
  13. P

    help me build my 331 stroker

    i have the chance to buy a 331 stroker kit on the cheap and i want to know what sort of things to expect to replace or upgrade. i had planned on the usual stuff, like oil pump, water pump, hoses, ignition stuff, etc. will i need different injectors? different maf, fuel pump? i already have an...
  14. P

    running rich but getting lean codes. 41 91

    my car runs pig rich but i get codes 41 and 91 showing both o2 sensors are indicating lean a condition. before i replace the sensors, i have longtube bbk headers. i really dont know much about mustangs-most of my experience is lt1/ls1 stuff but i have seen before when aftermarket headers keep...
  15. P

    Electric Fuel Pump. where do i mount it?

    by the way, are all holley reds super loud? im going to mount mine in wiper motor bushings and see if its better-but right now its very loud.
  16. P

    Electric Fuel Pump. where do i mount it?

    its always a good idea to put a fuel filter between the tank and pump, and then again before the carb. especially if your fuel tank is original.
  17. P

    tuning a demon carb

    if i turn the idle set screws in anything past 1 turn the idle starts to drop. i will lower the float levels to the lowest mark and see what happens. i was also concerned about the carb being unable to support my cam. advertised duration at .050 lobe lift is 224 deg. i found out later the...
  18. P

    tuning a demon carb

    by the way, the fuel pump is holley red, preset at 7 psi.
  19. P

    tuning a demon carb

    thanks for the replys. my carb is a road demon. 625 cfm vac. secondaries. the engine is 5.0 with gt40 alum heads and x303 cam. i have the floats at the center of the sights and the idle set screws 1 turn from being all the way in. can this be a timing problem? i didnt think the float levels had...
  20. P

    tuning a demon carb

    thanks for the help. i'll do some more research.
Top Bottom
Back
Forums
Menu