Search results

  1. SMOKEDYA

    Brakes help please

    What do you mean?I order the 3-2 conversion from MM and they say to keep the stock valve. peace john:p
  2. SMOKEDYA

    Electric fan help

    Ok so blue+black=high speed. black+black=low speed.I will go check it later or tomorrow.So are these designed to push air,or pull air?And i can say with the 2 blacks hooked up this sucker hauls ass!So if your correct and its on low speed now?I would hte to see how fast is hi speed!!!! :eek...
  3. SMOKEDYA

    Brakes help please

    Yes sir i did! Ok i will watch that.I have OEM 03 cobras front and OEM 94+ cobra rears,93 cobra M/C and a summit proprtioning valve.Before i did the mc and valve the brakes were soft but stopped good.....peace john:p
  4. SMOKEDYA

    Electric fan help

    So it has 2 grounds?I hooked it up to a battery to test it before i installed it.Blue to + and black to - it did nothing,thenswapped the 2 and it started smoking. I hooked up the blacks to +and- and it worked fine,then i swapped the 2 blacks and it still worked fine.But when i hook it up in my...
  5. SMOKEDYA

    Brakes help please

    Well i turned the rod on the booster in some tonight and that helped alot,so i will remove the m/c tomorrow again and turn it in more.peace john:p
  6. SMOKEDYA

    Electric fan help

    So i get a fan out of a mark VIII. I have blue black and black wires comming out of it.I hooked the blue and one black one up and it started smoking.So i hook up the 2 black ones and the fan is PUSHING threw the radiator,if i switch them it turns slower and then blows the fuse.Are these fans...
  7. SMOKEDYA

    Brakes help please

    I have been doing a little research since i posted this,and i was thinking it could be the adjustment rod in the booster?I did or thought iadjuted it correctly per mm's instructions.But i could be off?I will try to adjust it in some and try that?I do have the stock 89 booster tho.peace...
  8. SMOKEDYA

    Fuel rail crossover hose replacement?

    If i remember right?The stock cross over lines have a covering over them so what you see isnt the actual lines.But also i did the same.I cut the stock cross overs off and used high pressure fuel injection lines with clamps when i installed my 351 with stock fox rails!No leaks and about 2...
  9. SMOKEDYA

    Brakes help please

    I installed my 93 cobra MC and line locks and adjutable proportioning valve on my 89.I already had 4 wheel disc.Now the pedal is hard topush and it barly stops!Even after i fooled with the proportioning valve. Any ideas?peace john:p
  10. SMOKEDYA

    Intake bolt help

    Thanks
  11. SMOKEDYA

    Intake bolt help

    I would do studs,but either way I need to fix the threads. Plus I have ARP bolts now.peace John:p
  12. SMOKEDYA

    Intake bolt help

    So somehow today when i was TQ down my lower intake,i pulled the threads out of my AFR heads on one hole?! I was only at 15 LBS when it happened.So i need to know what size the bolt is so i can hellia coil it?I was thinking it's a 5/16 or 1/4" bolt threads?Peace john:p
  13. SMOKEDYA

    315/35/17 with 17x10.5 on 95 GT??

    I ran 315's also on my 95 so did a few buddies.Mine didnt rub but his did but nothing major or to worry about.Also you might need to message the inner fenders with a hammer,but still no worries there either.Trust me it will look bad ass when done!peace john:p
  14. SMOKEDYA

    Bad Fuel Pump: Any suggestions before buying a new one?

    The screen is color is fine,but i would still install a new one.As far as all that rust i would clean it out good.They make this coating to put on bare metal that will hold up to gas.Wire brush stuff and clean it good then recoat it with that stuff.It looks like moisture is in the tank,where do...
  15. SMOKEDYA

    E brake does not hold car from rolling: 91 GT

    Sounds like it just needs adjusted.Pull the drums make sure all the springs are hooked up,then put the drum back on and from the back side turn the dial looking thing.Then reinstall the wheels and see if that fixes it?You might want to turn the dial (adjuster) while the drum is off to see what...
  16. SMOKEDYA

    New look!

    thanks
  17. SMOKEDYA

    New look!

    Yes i did but couldnt see forking out $1500 for 1 wheel that i needed,so i bought my drag set up and other stuff.peace john:p
  18. SMOKEDYA

    Waste gate spring help..

    My WG is whatever comes with the POS ON3 kit.......I am useing a hallman pro series manual boost controller.With it turned all the way down i see 9PSI on my autometer boost gauge.peace john:p
  19. SMOKEDYA

    Waste gate spring help..

    I have 4 diffrent springs,and i need to drop down to the lowerest spring i have for now.I noticed the coils on the springs are diffrent thickness or diameters.So the spring that is the smallest is the low PSI?So the yellow spring pictured here would be close to 5PSI peace john:p
View older results
Top Bottom
Back
Forums
Menu