Search results

  1. AnthonyR23

    347 Break-In Error Codes Fuel Pump?

    I guess I should add that it is a 88 Mustang GT Convertible with a A9L computer.
  2. AnthonyR23

    347 Break-In Error Codes Fuel Pump?

    So I checked my engine off error codes and here is what I am getting: Code 96: Fuel pump monitor circuit shows no power - Power / Fuel Pump Circuits Code 82: AIRB solenoid - Solenoids and Air Injection I have a adjustable fuel pressure regular and fuel pressure gauge hooked up...
  3. AnthonyR23

    High Torque Mini Starter Question

    Well I haven't heard any grinding, I heard almost a buzzing, like it sounds like it is getting power, maybe not engaging some how. Just to verify that I have this right, like in the diagram, the old wire that used to be on the opposite side of the fender wall solenoid gets switched to the...
  4. AnthonyR23

    High Torque Mini Starter Question

    Hey guys, so I just installed my new high torque mini starter, had to drop the x pipe to get at the original starter. So once I got it in, I swapped the original starter wire to the other side on the fenderwall solenoid, and ran another wire that was necessary for the new mini starter. I hope...
  5. AnthonyR23

    Coolant Temp Sensor Wiring Question

    Hey, I was more curious than anything, I went to George Brown College and took the Electromechanical Technician Certificate Program as well as the Electronics Technician Program, but if it's a pain it's been awhile! I have a spal controller unit, so was kinda just curious if the ect sensor...
  6. AnthonyR23

    Coolant Temp Sensor Wiring Question

    Hey guys, so I have an extra Coolant Temp Sensor and am wondering if I can use it as just a temp sensor for my fan controller, there is two wires, but a normal temp sensor like for the gauge just has the one wire, if I solder onto one of the pins of the coolant temp sensor, could it be used the...
  7. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    Hey ya I was wondering about that, I will definitely try to get in there to tighten them down more after it runs for a bit, and will also check the oil. I think I am going to want to dump the oil after a couple drives, because I did leave the oil plug out to drip overnight when I had the milky...
  8. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    I got that permatex Right Stuff from Canadian Tire! So I ditched the end corks and used that. I have the intake on there now, just hand tight, and am not tightening till tomorrow morning. I re-read the Trick flow instructions, and it doesn't mention using those cork ends at all, so maybe that...
  9. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    okay awesome! I will try that! "Ditching the cork ends" and I will pick up some gasket cement aswell as the rtv sealer... thanks guys! I will let you guys know how it goes! Thanks!!!!!!!!
  10. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    I don't think I needed enough RTV sealer, so this time I am gonna go with a little thicker beads of sealer!
  11. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    See in the last pic how the gasket looks shifted, not sure how that could have affected the water ports though?? Don't you think the trick flow street heads should match the trick flow street intake pretty good, compared to lets say a trick flow intake with stock heads. You would think that the...
  12. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    More Pics
  13. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    Hey so I got the lower off, about 15 minutes ago, have to get ready for work, I did use that black permatex rtv sealer, it does look like the front shifted, because it is stuck out of place, but not sure if that would cause the water in the oil, anyways I want to make sure I do this right this...
  14. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    Hey its the trick flow street series with trick flow heads, all brand new.
  15. AnthonyR23

    347 Startup Break-in Cappaccino Oil!

    Hey guys, so what I thought was good news, I got the new 347 started up, probably 3 times, for about 2 or 3 minutes, noticed a bit of a gas leak on one of the fuel rails, so I fixed that, then it looked like a bit of a water leak at the back, which seemed to go away after I dried it off, and...
  16. AnthonyR23

    Won't Start! 347 Break-In!

    Thanks! Will start at #1!
  17. AnthonyR23

    Won't Start! 347 Break-In!

    Hey guys, so everything is ready to go on my 347 trick flow build. So I got as far as being able to turn over the engine, even though it is kinda struggling, not clicking but like it looses cranking power or something, I did order a high torque mini starter yesterday, so that should come by the...
  18. AnthonyR23

    347 Startup Trials! So close!!! Breakin!

    Hey so I set my fuel pressure at 45 psi!! Thanks!!! My battery is okay and is charged right up, but it is trying to start and is turning over, but it does sound like the starter is struggling, so I just ordered a hi torque mini starter, hopefully that should help me out. It should get here...
  19. AnthonyR23

    347 Startup Trials! So close!!! Breakin!

    anyone know what I should set my fuel pressure at?? To start??
  20. AnthonyR23

    347 Startup Trials! So close!!! Breakin!

    Hey guys, so any advice will be much appreciated, me and my dad tried to get my new 347 trick flow build up and running, checked engine off error codes and everything is looking good set timing to a base 10 degrees, and have about 60 psi of fuel pressure. I am going to take my battery in to...
Top Bottom
Back
Forums
Menu