Search results

  1. K

    CHEAP 302 Doner Car?

    I'm bouncing around the idea of buying a running 302 car as a doner for my 65 coupe. Pulling the 302 installing new bearings & rings, new cam, new distributer, removing the EFI, installing an intake & carb. Strip the car of its drivetrain and sell (or give) the body to a salvage yard. I do not...
  2. K

    LED replacement tail light bulbs? Anyone use them?

    I searched, didn't find the answer I'm looking for. Anyone use these? Pros & Cons? Photos? They are super cheap even though they will take a month to get here...
  3. K

    1989 Bronco as donorcar.

    Im not an expert but the EFI, intake ect. from an 80s mustang should swap to your current 302. Try searching for this.
  4. K

    Size of Glasspacks

    I was thinkin about Cherry Bombs!!!
  5. K

    Size of Glasspacks

    Currently I have a mainly stock 289 and plan to keep it very mild. I'm puting my Christmas list together and asking for Tri-Y headers and plan to go w/ an "H" pipe w/ glasspacks. I currently have single exhaust into one glass pack 29" long and 3.5" OD diameter. It really isnt too loud and...
  6. K

    65 Driveshaft Length Question - Photo attached

    I decided to go w/ 51" from u-joint center cap to center cap. Thanks for your feedback I really hoping this driveshaft will work w/ a T5 later.......years later at the rate I'm going.
  7. K

    65 Driveshaft Length Question - Photo attached

    Thanks all, you have helped me make my decision, gonna stick w/ 1" and discuss w/ the driveshaft shop prior.
  8. K

    65 Driveshaft Length Question - Photo attached

    I just re-read this and that makes sense, so your saying about an 1" is workable. Any thoughts on 1.5" (is this too far out of the trans) so I can maybe fit a T5 later w/ maybe no drive shaft mods.
  9. K

    65 Driveshaft Length Question - Photo attached

    I'm using a Lincoln Versallies 9" which originally used a rear disk type driveshaft attachment w/ a slip yoke driveshaft at the trans end. I do not have this driveshaft and I am moding the mustang driveshaft to work w/ a 9" axle yoke I purchased for the versallies rear end. I attempted to find...
  10. K

    65 Driveshaft Length Question - Photo attached

    I need to have my driveshaft cut and have a different yoke welded on the axle end so I can use a large u-joint to match the 9" yoke (I tried to find a adapter u-joint w/ no luck and have given up on this). I need to know how much clearance is needed from the end of the C4 transmission tail...
  11. K

    3 Point Belts w/o removing headliner - coupe

    Yea, thanks for the pics! Thats exactly what I was picturing in my head. I will start looking for a GC w/ black interior. My other hobby is Jeeps anyways. Anyone think its a bad I idea to omit the loop mounted to the area above the rear glass and just pull the belt over your shoulder. Its...
  12. K

    3 Point Belts w/o removing headliner - coupe

    Thanks, any pics would be great! I know I can source GC belts real easy.
  13. K

    3 Point Belts w/o removing headliner - coupe

    OK.....so you have no upper loop to reach back over your shoulder to grab? The belt is pulled over the seat, then over your shoulder and connect across your lap? Any pics and suggestion of what car you pulled from? Thanks.
  14. K

    3 Point Belts w/o removing headliner - coupe

    Is it possible to install 3 point belts w/o removing the head liner and instead mounting the shoulder point to the body below the head liner in a coupe (inside from the back window)? If anyone has this set up, how comfortable is it? Also is there a good doner car for a black interior or should...
  15. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    Ok, I will try this. I already purchased a combo joint (which I still have) and attempted to swap the cups which came out of the stock joint (my old joint)and the stub that the needles ride on was too wide and would not fit the old stock cup? I know this seems like a simple question and I'm...
  16. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    http://www.dennysdriveshaft.com/p410_mustang_1964_1966_rear_universal_joint_with_inside_snap_ring.html?submit=More+Information This is the joint I need, but I would have to buy a 1310 yoke for the axle Vs the 1330 I have, so about for $100.00 I will just have my driveshaft shortened and a...
  17. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    I called Ford and was told this is the olny option they have. Ford Racing M-4635-A Ford Racing U-Joints Includes Four 1.0625" OD and Two 1.125" OD Caps and Locking Clips Allows Small and Large Ford Drivetrain Components To Be Interchanged My stock driveshaft is using a 1.0" cap w/...
  18. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    Summit dosent have the joint I need and refered me to Lakewood & Inland Empire Driveline. I called all any everyone says my combo dosent exist. Stock Driveshaft axis is 3.15" length (cap to cap) w/ a 1.0" cap. Inside locking clips w/ a distance of 2.396 apart. 9" Yoke axis is 3.622...
  19. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    I bought a 4" yoke off ebay and went to 3 different auto part stores and called Jegs and Summit and they do not make a compatible u-joint for my stock drive shaft and the yoke which came out of 70-80s truck. So what yoke has everyone else used? I know some people on the forum have used Bronco...
  20. K

    Front suspension rebuild

    I plan to do the Shelby drop as the same time. Are the caps pressed on? I really haven't even investigated yet. Is the lower arm able to be rebuilt?
Top Bottom
Back
Forums
Menu