Search results

  1. stangman16

    No Start - Fuel Pump Not Getting Power

    Thanks! Went through the list and found that the PCM power relay was only putting 4.6 volts on the red wire and at the injectors. Changed the relay and the car now starts! Thanks again!
  2. stangman16

    No Start - Fuel Pump Not Getting Power

    Hello, My 1966 mustang with a '93 EFI system was put outside for about a month now and cannot get it to start. The engine cranks over and I noticed I did not hear the fuel pump prime when turning the key to "on". I tried bypassing the fuel pump relay and the pump does indeed work. Changed the...
  3. stangman16

    Efi Swap In A 68 Mustang, Wiring Help

    Get the book: how to inderstand, service, and modify Ford fuel injection& electronic ignition controls. Its a little daunting at first glance, but once you study the book a little and with the help of the diagrams it'll ease out on the complexity. I took a brand new harness and dont see any...
  4. stangman16

    '66 Mustang Quarter Panel Extensions

    What about using Muggyweld 'super alloy 1' solder? Anyone tried this yet?
  5. stangman16

    Efi With Stock Fuel Sending Unit Questions

    I used the Ron Morris sending unit and bracket along with a Holley inline fuel pump.. gotta have the 40 psi as advised previosly.I used the old fuel lines as my return line and ran new aluminum lines with AN fittings and high pressure fuel hose to connect the stock 91 fuel filterin between.
  6. stangman16

    '66 Mustang Quarter Panel Extensions

    Been thinking about it, and I still have some lead-free body solder left over from the quarter panel install.. think that will work with the pot metal extensions to quarter panels?
  7. stangman16

    '66 Mustang Quarter Panel Extensions

    Much to think about... sure don't want it cracking, and good to know it can't be welded.
  8. stangman16

    '66 Mustang Quarter Panel Extensions

    Has anyone blended the quarter panel extensions with the quarter panels on a '64.5 - '66 coupe? I'm curious what is the best way to blend them together? Just weld them up or tighten them down and use filler or epoxy putty? anyone have any pics? I'm also planning on blending the panel between...
  9. stangman16

    New Forum Questions, Answers, Feedback, and things that make you go, "Hmmmmm"

    ha, I blindly missed it - thanks!
  10. stangman16

    New Forum Questions, Answers, Feedback, and things that make you go, "Hmmmmm"

    Where did the Forum Search option go ? :shrug:
  11. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    Also, as far as paint goes im not looking to strip the whole car down to metal other then the quarters, is it okay to sand with 40 d epoxy over the prior urethane finish and then filler on top?
  12. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    Yeah I appreciate the pics and all the help, im still having a hard time with the door gap and lining up at the bottom. I took the panel off to finish prep work and im hoping to get things done by Saturday so I can start lining it up and welding it in. Is it easier to sheetmetal screw the door...
  13. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    Ok - will do, I'll take the panel off and fix as advised. Thank you!
  14. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    Thanks! That worked great! Upon test fitting the panel I just cannot seem to get the gap flush where it meets the piece right infront of the trunk. The best I can seem to get it is about 1/8th an inch or so. Everything else seems to line up okay except I'll have to massage the door area at the...
  15. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    I'm still slowly getting things done... at the point where I took out the rear quarter window and small weatherstrip piece, and I see spot welds on the quarter panel but they look as if it will be hard to get to and impossible to grind once I get the panel off. Im curious to know whats the best...
  16. stangman16

    Made my own T5 shift stick

    I'm interested! Was contemplating cutting my old 4spd hurst shifter but this is much better if the price is right, PM me when you figure out how much you are going to charge
  17. stangman16

    '66 Mustang Rear-end

    Awesome - thanks!
  18. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    Thanks for the details - that will definitely help alot! Is it necessary to use lead again after welding in the new quarter?
  19. stangman16

    '66 Mustang Coupe Full Length Quarter Panel Removal ?

    How do you remove the quarter panel on a '66 mustang coupe where it meets the roof? I know there was lead used where the two pieces are together and I'm curious what the best method (and safest) of removal is?
  20. stangman16

    '66 Mustang Rear-end

    I have the wrong rear-end in my '66 mustang as it is about 2" wider causing my tires to be cut by the quarter panels. It's an 8" rear with 28 spline axles and I have acquired a '66 mustang 8" rear-end housing and I would like to know if I can just transfer the 3rd member over and get '66 mustang...
Top Bottom
Back
Forums
Menu