Search results

  1. S

    Which subframes to get?

    Do you guys know anything about the cheap subframes on ebay? Here's a link: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=42609&item=2458909217 Do you think they'd work right?
  2. S

    How much FWHP and RWHP on my soon to be done setup?

    I think your going to have some problems with your combo and SD. That cam isn't the best from what I've been told, doesn't pull enough vacume. When I put in my new engine this summer it wouldn't run right, and I tried everything to fix the problem (new sensors, plugs, wires, etc.). I finally...
  3. S

    Need a new mod!!

    Is zero vacume with the line off and plugged like the conditions of WOT.
  4. S

    Need a new mod!!

    I've got an A/F ratio gauge mounted on the A-pillar, but I haven't gotten a chance to hook it up. So you think I need to up the psi to at least 38 then go up in increments from there? Thanks for the help.
  5. S

    Need a new mod!!

    I've currently upgraded the MAF to a C&L 73mm and switched to 30lb inj, does anybody know what fuel pressure I should set the AFPR at? I've got it at about 35 psi at WOT not sure if this is right or not, but it does run good and I don't have any issues with it yet. I'm also curious as to what...
  6. S

    after head swap starting problems

    did you make sure you put all the grounds back on correctly and make sure the connections where clean? what about the vacume hoses for the intake and such? it sounds to me that maybe you forgot a vacume hose or ground cable. good luck casey
  7. S

    HeaTER CORE

    351wRusty I had the same problem as you with the air blowing out of the defrost (not after changing the heater core or anything though). My problem was that there is a vacume hose that goes up under the drivers side dash and it connects to a vacume canister that looks like a small fuel filter...
  8. S

    Are all lower control arms interchangable?

    I also have another question, does anybody run the Grantelli upper and lower control arms? Are they any good or should I look at some different brand? Thanks Casey
  9. S

    Are all lower control arms interchangable?

    So what you guys are saying is that all the 87-93 that have the live axle will all be usuable?
  10. S

    Are all lower control arms interchangable?

    I've seen some LCAs selling on ebay and some of the say they will fit 87-03 and others say 99-03. Are they all interchangable or are they sepecific to the year of car? Sorry for the stupid question. Casey
  11. S

    Typhoon Upper intake fit a Edelbrock lower?

    I currently have a edelbrock performer upper and lower intake. Last week when I was putting my upper on, the back ear where the bolt goes through broke off. It ended up costing me $60.00 bucks to put it back on, and tonight when I was putting new injectors in both the back ones broke...
  12. S

    What size mass air meter for my combo? And I think I fried my 6al!

    Doesn't anyone have any suggestions on either the meter or on a way to get my MSD fixed?
  13. S

    What size mass air meter for my combo? And I think I fried my 6al!

    ttt
  14. S

    What size mass air meter for my combo? And I think I fried my 6al!

    Well I've got two questions for ya. The first is what size mass air meter do you think i should run with my combo(in sig)? I've already got a 73mm C&L calibrated for 30#ers. And I've also got a friend who is selling a 80mm C&L calibrated for 24#ers. I also already have 30# and 24# injectors...
  15. S

    What's the best fluid for TKO?

    They sell a Mobile 1 transmission fluid that is supposed to be the same or it might be the same as the GM syncromesh fluid at Autozone. The paper that came with my Tremec said either GM syncromesh or some other type and it says on the back Mobile 1 that it can be used.
  16. S

    5.0

    If the MAM is a Pro-M it should say what size injectors it is calibrated to on the meter below the "Pro-M" letters on the sensor. Casey
  17. S

    Fly-Cutting Pistons....

    I've got the Crower 15511 cam with 1.7 rr and Edelbrock Performer heads and no problems (although they are 1.90/1.60 valves). Everyone has told me the lift on the Crower w/1.7's 500/518 no one has ever told me the numbers you posted although there's only a couple thousands of an inch. Casey
  18. S

    Where can a find a 24# sample tube, for C&L meter?

    ttt
  19. S

    Where can a find a 24# sample tube, for C&L meter?

    I'm looking for a 24# sample tube for 73mm C&L mass air meter 89-93. Where can I get one cheap or does anybody have one forsale cheap? Need one quick. Thanks Casey
  20. S

    Getting Pro-M 75mm Bullit MAM, but don't know what its calibrated to?

    I also have one other question. Would a 75 or 77mm MAM and 30lb injectors be to big for my combo? Should I get 24's or will 30's be fine? Thanks
Top Bottom
Back
Forums
Menu