Search results

  1. z9_87

    I Hate Allan Bolts And Ford!

    There are a lot of things I ask why they did it that way and you can plainly see it would be easy if they did it another. Actually I'm usually like why the **** did they do that.
  2. z9_87

    Dream Engine?

    are those hemi heads? I thought they had to have a spark plug down the middle through the valve covers if they are.
  3. z9_87

    Q's about Cartech intake

    If it fits the stock lower it can't be that good.
  4. z9_87

    Dream Engine?

    !puts on flame retardant vest! TT stroked ls1or ls2 in a 75ish TA
  5. z9_87

    finally fired the 331 up

    electronic fuel injected, well you have efi. Just not mass air. You should get a chip burnt though.
  6. z9_87

    finally fired the 331 up

    you did a 331 and cam with no chip burt? If not you could gain a lot of power and it should run even smoother if you did.
  7. z9_87

    Mustang Missing like CRAZY. unless I gun it

    Same thing here, while it was missing at low rpm's i pull up next to a civiv, and they are laughing at me, so I ask if they want to race a 7cyl thunderbird. Little did they know the miss cleared up about 2k rpms :) Makes a good sleeper!
  8. z9_87

    Mustang Missing like CRAZY. unless I gun it

    I just fixed mine, it was a plug wire bad, I couldn't get it to arc so I just wrapped the driver's side wires with rubber elec heat resistant tape and problem gone. So it was a plug wire one of 5-8.
  9. z9_87

    elec fan

    wait camaro's had electric fans in 85 but stangs didn't get em until 94? hmmmm.
  10. z9_87

    finally fired the 331 up

    Yeah you would have to re-burn the computer.
  11. z9_87

    difference between tracklok and posi?

    GM used to have a posi that used clutches or something and you could hear it click when you turned at higher speeds.
  12. z9_87

    o2 sensors

    Get a 6 sided 7/8" inch wrench with a small hole on one of the sides that will let you put the wires through. That way you wont round it and it'll hold with however much torque you give it.
  13. z9_87

    engine identification question

    Yeah get the casting numbers off of it, I'm sure that would tell. Right?
  14. z9_87

    o2 sensors

    I can't remember the size but you just use a wrench, maybe 1" or 3/4", it's bigger.
  15. z9_87

    wierd sound after running good for 2 weeks

    I don't know why I would need a new lower intake gasket but I might pull the injectors and have em tested. On my previous post, I spoke to soon, took it out for awhile today and it started off fine then after a while it was missing and then it was okay then missing.
  16. z9_87

    wierd sound after running good for 2 weeks

    Well everything checked out fine, TPS voltage is at .97 at wot. No exhaust leak. I was thinking something with the fuel. Cause it is an on again off again problem. So I put some seafoam in the tank and I'm going to run a little through the intake to see if it cleans the injectors, also put a...
  17. z9_87

    New headgaskets slightly bent (ok to use?)

    if these are used head gaskets then dont re-use them. Otherwise take them back for new ones if you think they're bent.
  18. z9_87

    New headgaskets slightly bent (ok to use?)

    Like a bend so there is a crease in the o-ring and paper material?
  19. z9_87

    50 Amp Switch for Taurus Fan

    Get 2 relays one for high and one for low.
  20. z9_87

    50 Amp Switch for Taurus Fan

    Actually it's more a matter of time that the switch melts or burns out. There have been a lot of recals and such over the years because the factory wires things straight through the switches to save $1 on every car.
Top Bottom
Back
Forums
Menu