Search results

  1. MikeR351w

    Starter wont Diss-engauge

    Thank you for a response. If i have the wires on the CORRECT side of the starter relay but not in the correct order, for instance the yellow in front of the red instead of the red in front of the yellow , would that cause the 1-2 second delay???? Thanks again!!!
  2. MikeR351w

    Starter wont Diss-engauge

    should i replace the solenoid anways?????
  3. MikeR351w

    Starter wont Diss-engauge

    Ok i got a 92 5.0 mustang. Out of nowhere the starter starts to hang up. It takes like 4 seconds after the car starts to diss-engauge. This might be due to the fact that the lower bolt was not fully tightened. Anyways i had a new bolt put in and it still did it. Then i put in a new starter...
  4. MikeR351w

    dyno results

    what dyno results can I expect from a 92 5.0 LX with 120k and a auto trans. I have the following mods -Throttle body -FULL exhaust / No cats/ Flo Pro mufflers/ and headers -Alluminum driveshaft -cold air kit -underdrive pulleys So, what am I putting to the rear wheels??
  5. MikeR351w

    1/4 Mile, Horsepower Estimate

    I have a 92 Mustang 5.0 with the auto trans. I have a 8.8 rear with a 3.27 posi. I also have an aluminum driveshaft, chassis stiffening, and a curb weight of about 2900 pounds. My performance mods include a 65mm throttle body, cold air intake fenderwell, underdrive pulleys, no air cond., full...
  6. MikeR351w

    Heads

    The car is an 87 that used to be a four cylinder. I dropped in a 93 5.0 and did a ton of weight reduction. I am guessing she has around 240hp now. The only thing that I have not changed is the wimpy 7.5'' rear end. I dont know what gears are in it now, any guesses?? It does have a rear...
  7. MikeR351w

    Heads

    I have a 93 5.0 with 115k miles on it. It has the auto trans, a larger throttle body, full exhaust, alluminum driveshaft, and a cold air intake. Would putting on brand new heads kill my engine?? Also will I need to change the camshaft with new heads? What is the best intake to go with a set...
  8. MikeR351w

    Trick Flow Heads+115k 5.0=?

    I just got a deal on some brand new, out of the box Trick Flow Twisted Wedge Alluminum heads. My engine is a 93 5.0 with the auto trans. So far it has a larger throttle body, full exhaust, and an air intake. With 115k miles on my engine now, will putting brand new heads on it kill the...
  9. MikeR351w

    EGR, SMOG & P/S Eliminator kit

    I will be running high flow cats from BBK. Will the steering be dangerously compromised if I take out the pump??
  10. MikeR351w

    EGR, SMOG & P/S Eliminator kit

    Im bringin this one back guys! Come on, someone has to have some input!
  11. MikeR351w

    EGR, SMOG & P/S Eliminator kit

    I have just about had it with this bracket I bought! I might as well just buy a underdrive pullley kit from March Perf. I want the Alt, Crank, and Water pump kit. Will not having a smog pump make my 5.0 run bad or change the idle?? I currently dont have the EGR hooked up since i think a line...
  12. MikeR351w

    A/C Eliminator Install

    not to mention the whole thing is out of belt alignment and the way i have the black bracket is the ONLY way it will fit!
  13. MikeR351w

    A/C Eliminator Install

    only one of the bolts goes through the pump!! The other hole that is lined up with the silver bracket is too small!! The brass bolt is too big for it! The only way it will fit is if i move the pump up 2 more inches and sandwich the black bracket in between the bolt and the pump. Do i have...
  14. MikeR351w

    A/C Eliminator Install

    Still cant figure it out!!!!! The alignment is off and one of the long brass bolts does not fit through the bottom hole on the P.S pump. I had to put it out side the bracket and pinch the black bracket against the pump then threaded the bolt on the lower silver piece. That was the easy part...
  15. MikeR351w

    A/C Eliminator Install

    got a pic??
  16. MikeR351w

    A/C Eliminator Install

    THANKS!!!!! Please look for the instructions anyways, and did you get a new belt for you car?? The power steering pump is now slightly higher or a lot higher than stock???
  17. MikeR351w

    A/C Eliminator Install

    Anybody ever bought the a.c eliminator kit from Ford Racing?? I ordered it from a dealer and they forgot the instructions!! Anybody have pictures or know how to put it in??? Its the one with two brackets, 3 bolts and 2 long bolts. PLEASE HELP!!!!!!!
  18. MikeR351w

    Which is easier swap, 5 Speed to Auto or 4 cyl to V8?

    Well I would say buy a V-8 with a 5-Speed. If you have the $$$$ that is. If it is slim pickins where you live for stangs than broaden your search area. Maybe take a road trip with a friend or a train. Then drive the beast back! If you dont have the $$$$, the buy a 4 cylinder with whatever...
  19. MikeR351w

    Stater Relay PICTURE NEEDED!

    my battery voltage is high enough. It reads in the middle of the gauge. I did not have a ground attached to the firewall but when I hooked it up I hear the same noise. What could it be??? I know the car wont start without the fuel system hooked up but I just want to hear her turn over for...
  20. MikeR351w

    Stater Relay PICTURE NEEDED!

    Anyone with a 89 5.0 that has a pic of their starter relay SEND IT TO ME!!!!! With a graphic description of where the wires plug in. Also, where does the MAP sensor vaccum hose plug into the TEE?? (the triple way connector on the far passenger side of the engine compartment). Where does the...
View older results
Top Bottom
Back
Forums
Menu