Search results

  1. ONEBADPNY

    t-5 trans help

    i am in need of a t-5 for my mustang. i am really short on cash so i plan to go to a u-pull-it and see what i can find. i know a thunderbird turdo coupe will work, but what other cars can i look for? are 4 cylinder mustang the same 5-speed? it is just to get it back up and running. i can handle...
  2. ONEBADPNY

    85 distributor wiring

    duraspark II carb motor. i am not sure on the instruction sheet.
  3. ONEBADPNY

    85 distributor wiring

    i mainly need to know were to hook up the wires off the distributor. i don't know where to hook them up
  4. ONEBADPNY

    85 distributor wiring

    i am trying to wire up my mallory hyfire ignition box with an 85 distributor in a 66 mustang. it is carb if it matters. i don't know what to hook the three wires coming out of the distributor too. also there is one wire on the mallory box that i don't know were goes either. the wire fromthe box...
  5. ONEBADPNY

    NE1 order new rearend

    has anyone ordered a new rear end before from currie enterprise? just wandering about your experiences with them. thinking of buy one from them.
  6. ONEBADPNY

    lets talk 8.8

    i have been reading about 8.8 swaps in early mustangs. i have a 66. i know there will be some welding involve but i am looking for more info on this swap. also what about the explorer rear end?? thanks for any help
  7. ONEBADPNY

    electric fan ???

    thanks guys i read more into the web page and it does state that it can handle the markvlll fan so the 35 will be fine.
  8. ONEBADPNY

    electric fan ???

    black sun 5.0 which kit did you buy for your sn95 fan? i need to buy one but not sure which one i need. 35amp or 65 amp?
  9. ONEBADPNY

    pictures of my project

    more
  10. ONEBADPNY

    pictures of my project

    took some pictures in the garage today of my 66 coupe. hope to have it running by summer. needs new brake lines run and a rear put in then goes the latemodel 302 in with a t-5.
  11. ONEBADPNY

    need help with centerlink

    i am putting together the front end on my 66 mustang and i swap out the steering centerlink, end links,etc. for v8 pieces. i put on the pitman arm and idler arm and i have to push up on the centerlink in order to get it together. its like the idler arm is to high compared to the pitman arm. am i...
  12. ONEBADPNY

    17" wheels on a 66

    what size tires can i run safely on the front and rear? i am getting a 17x8 or 17x7 wheel not sure yet. what size back spacing will i need? 4" be enough? anyone has pictures i would like to see them too. thought about bullit wheels first but now maybe torq thrust ll's.
  13. ONEBADPNY

    oil pan question

    i have one off a 67 289 but it didn't look like the bolt hole would line up. i did not try to put it on the car so maybe i need to try again. thanks
  14. ONEBADPNY

    oil pan question

    will the oil pan on a 95 302 fit into a 66 coupe.
  15. ONEBADPNY

    help with motor

    my friend said that it would be easier to use a mech. fuel pump. but if it comes down to it then i will go electric. can i use the 95 timing cover then? thanks for the help.
  16. ONEBADPNY

    help with motor

    i am getting ready to put a 95 roller motor in a 66 mustang and go carb with it. i have a few new questions now though. what timing chain cover do i need for running a mech. fuel pump? the one off the 289 will not fit.also to run the fuel pump there is a pin in the cam sprocket but what do i use...
  17. ONEBADPNY

    gt40p head users which headers

    i am thinking of getting some short tube headers for my car. i think my long tubes are starting to rust out. so i will not get any more mac components. i will spend a little more money this time. i was wandering what everyone else runs? or if you have had both? i was wandering if i would see...
  18. ONEBADPNY

    GT40P Heads Any Good?

    they are great heads. the only headers that you would really have problems with are equal lenghts. they will not fit. but most long tube and short tubes will work. my friend has almost the same setup as me but he has ported trickflow heads, trickflow stage2 cam and an rpm intake. i pull away...
  19. ONEBADPNY

    Are 11's possible with my heads??

    i ran a best time of 12.3 with all seats removed and spare tire from my lx with unported gt40p heads. i run slicks and skinnies with 4.10 gear though. i want to get closer to the 12.0s with mine too. but i want to do it with out porting my heads first. i say you should get some slicks and launch...
  20. ONEBADPNY

    How to get tint adhesive off with out destroying rear defroster...

    i used fingernail polish remove that my wife had. it has acatone in it. wipe on and wipe off.
Top Bottom
Back
Forums
Menu