Search results

  1. S

    tried and true rear suspention

    I am mirroring a buddies drag setup...wild rides anti roll bar, wild rides torque box reinforcements, coilovers, and track locater (similar to panhard) he runs consistent 1.4s onn an all motor car that runs 9.45 1/4......sounds like trued rear suspension setup to me..and it was pretty cheap with...
  2. S

    Hid's Installation Question

    just to be clear I didnt read any of the posts made by everyone else cause I dont have the time but wanted to put my two cents in. I have Hi/Lo HIDs in my factory style housings on my mustang and they work fine..no glare. I also have HIDs in my other two cars as well. Most good plug in play HID...
  3. S

    460 swap...FMS Pan question

    yes you will need to contact FMS or Canton to get the pick up bolt..local shops might carry one. I did a rear sump conversion on a cleveland and the bolt replaces a main cap bolt on third cap and has stud sticking off the top to hold pickup down.
  4. S

    Installing A 10 Point Rollcage!!!..

    pics... You can check out some pics here norcal1320.com I havent uploaded my completed pics yet but this is the mild steel wolfe racecraft 8 point cage with Alston swingouts (not chris alston) this cage is legal to 8.50's....These are some of the work in progress pics..I will get soe...
  5. S

    how do i tell what size my lines are for my n2o. and do these jet sizes sound right

    call them....
  6. S

    Anyone Running the PA SFI Bell Housing?

    I am running a PA SFI bell housing. depends on what size convertor you are running. i believe the PA bel housing will fit both sizes but if you have a 11" or smaller convertor then you are definately a 157 tooth. I am running a 9.5" Convertor and a 157 tooth flexplate. The starter should not be...
  7. S

    Installing A 10 Point Rollcage!!!..

    go with a wolfe racecraft cage...they make the cleanest tightest fitting cages out. I have an eight point in my 90 gt now and the fit is awesome. You can get chromoly from them (lighter and stronger) and have it prebent/jigged/notched so any fab shop can install it in one to two days...I have...
  8. S

    Flexplate Woes

    Do you have a convertor? If not where are you getting the bolt center? what spline input shaft does you C4 have? I am running a C4 with 26 spline input shaft and I have a 157 tooth flywheel and you buy the convertor to match the flywheel. This combo will fit in all ford bellhousings...the...
  9. S

    EFI - Carb conversion...?

    I apologize, as I posted and then remembered I could search the forums...I already found the www.jason.fletcher.net and it was quite helpful...as for the smog emissions thing...dont care but thanks for the concern. Its pretty much a strip only car so I am not concerned with that. I am already...
  10. S

    EFI - Carb conversion...?

    Anyone converted their efi to carb? I want to know what electrical I can take out safely or is there a kit or soemthing to do the conversion?
  11. S

    best sub frame connectors

    My friends 84 t-top had the Maximum motorsport full lengths and our exhaust shop welded them in for 50$ well worth it. I am running the through the floor sub frames from Wolfe Racecraft...they make a nice set of full lengths also but I would go with any 2"x3" full lengths....
  12. S

    Auto trans Shifter ...

    I thought I asked here but I guess not...What shifter does everyone run with automatic tranny? I have a reverese manual valve body...
  13. S

    T5 to C4 Conversion....help...

    thanks thanks for the info...I was told by serveral auto "hating" t5 owners (nothing against T5 owners. I own another one as well) that it would be costly and I would need a new cross member and supershort drive shaft. Thanks again for the info.
  14. S

    T5 to C4 Conversion....help...

    I am currently converting my 90 GT T5 to a C4 automatic. Does anyone know what all is involved. I havent been able to find any automatic crossmembers around my area so I couldnt compare them to see if they were diff...also drifeshaft length? Any help would be appreciated. Oh yeah and I am moving...
  15. S

    Front Suspension Upgrade....K Member

    Any problkems with the Granatelli kit? I was looking at those as well but no one had anything great to say about them. But I have a friend who was running deep 10 s on a GP kit for three years with only one problem ( r&p mounting points) Thats why I went with it. thanks for the infon...
  16. S

    Best fitting Cowl induction hood.

    Cervinis... I have a Cervini and it is perfect fit...
  17. S

    Front Suspension Upgrade....K Member

    I searched the tech threads and couldnt find anything about k members...I just ordered a Ground Pounder K Member and am going to use ground Pounder A arms and coilover kit for my 90 GT Hatch...I also purchased a flaming river manial r&p and wanted to know if anyone has similar setup? Do I need...
View older results
Top Bottom
Back
Forums
Menu