Search results

  1. moonraker

    Global West UCA question

    I had them in '68 and there were no issues. But I had to go back to stock ones due to wheel fitment.
  2. moonraker

    what size-coolant hole in 351W intake?

    Thank you all! It looks like 1/2" NPT
  3. moonraker

    what size-coolant hole in 351W intake?

    I need help - can someone tell me what size thread (what adapter) I need to connect heater hose to the hole in lower intake on 351W engine? I live in Russia and I'm not very good at AN or standard threads.... in the picture it's right below blue fuel rail adapter...
  4. moonraker

    stock-style UCA for '68?

    Thank! Yes, I have only 1" drop. So, I can just buy 70-73 stock arms and they fit fine and don't change any steering geometry?
  5. moonraker

    stock-style UCA for '68?

    I need to buy stock-style upper control arms for my '68 Fastback. Can someone point me to vendor that sells such arms with ball joint mount modified for shelby drop? I searched but I could only find stock geometry arms. But I remember that someone offered modified UCA.....
  6. moonraker

    need help w?/Unisteer R&P

    I've installed Unisteer R&P on my '68 Fastback. I need small taper tie rod ends. But in my package there were 3 big taper tie rod ends and only 1 small taper tie rod end. So I need one more small taper tie rod end. I send Unisteer 2 e-mais asking if I can buy such part but they haven't replied...
  7. moonraker

    Wich wheelstuds

    OK, I got them installed - they fit my combo just fine. but I guess someone may run into problems - the thread doesn't go all way to the knurl. so with the brake rotor installed I had about 5 mm from the thread end to the rotor surface. my wheels are 8 mm thick at the stud holes so this was OK...
  8. moonraker

    Wich wheelstuds

    i ordered these Moser Engineering 8250 - Moser Engineering Wheel Studs - Overview - SummitRacing.com
  9. moonraker

    Wich wheelstuds

    I'm doing the same conversion. Original studs won't fit - they are too short for the combined thickness of brake rotor + alloy wheel. I ordered some studs from Summit Racing but I live in Russia and it takes a while for the packages to arrive. I know it cleared Russian customs so it should be...
  10. moonraker

    how to attach '68 gas filler neck

    thank's for the tip! :nice:
  11. moonraker

    EFI harness options

    yes, there's a parameter in calibration that tells computer what tranny is used. but really it doesn't have much effect. the computer sences if the engine is in neutral(or clutch is depresed for manual tranny) or in drive (or clutch is released). that is senced via simple switch that shows 0...
  12. moonraker

    how to attach '68 gas filler neck

    thanks! where's my old file....
  13. moonraker

    how to attach '68 gas filler neck

    does it slide into the hole from the outside of the body? it seems logical to me but it doesn't fit through the hole....
  14. moonraker

    EFI harness options

    AFAIK that generation of computers was unaware what tranny was bolted to the engine. so yes, you can use a9l from manual car with AOD
  15. moonraker

    Are front bump stops really necessary?

    Thank you! It wasn't $2500, I just use their coil-overs, not the whole set-up. But I live in Russia so the shipping cost drive $40 to $140 (or maybe more - those stops are heavy...)
  16. moonraker

    Are front bump stops really necessary?

    I plan to use TCP front coil-overs on my 68 Fastback. My original bump stops are rusted beyond repair. Do I really need to replace them or I just can do without bump stops at all?
  17. moonraker

    Pls, help identify this bracket - 68 Fastback

    my valances were replaced and the new ones don't have holes for guards
  18. moonraker

    Pls, help identify this bracket - 68 Fastback

    Yep, that's what they are! Thank a lot! now I can put them away - I'm not going to have bumper guards at all.
  19. moonraker

    Pls, help identify this bracket - 68 Fastback

    Since the first body shop was a mistake and the second one did a lot of body work, I have various bits that are not installed on the body. I figured most of them but this bracket puzzles me. Can somebody tell me where this supposed to go?
  20. moonraker

    68 tailight bezels question

    Thanks for the input, but I live in Russia and I doubt that any seller will pay for the shipping back to the States. Can you tell me what the difference was between 67 and 68 bezels? I cannot move it higher since it barely fits in the holes - the holes are spaced apart further than mounting...
Top Bottom
Back
Forums
Menu