Search results

  1. Nutty 5.o

    The Journey To Find A Fox. Found A Cobra Instead.

    I actually put in power seats from a 93 cobra in my 90 LX. The covers are a funky plastic piece that covers the entire front all the way to the rear bolt on the outside facing door. If you find my old progress post I may have some pics. Or can try and dig them up.
  2. Nutty 5.o

    Cobra Bumper Insert Factory Install

    Both friends had done this to their cars. Ultimately they used Cervini's cobra insert kit and had body shop bond and finish it to look one piece. Came out good but personally prefer the insert as it is: an add on.
  3. Nutty 5.o

    For Sale Misc. 5.0 Mustang Parts New & Old

    Here’s better pic of the rim/tire.
  4. Nutty 5.o

    Gt40 (3 Bar) And Gt40 Intake Install Cost?

    I think that's the best decision. Subframes will make the car much more fun to drive on top of the benefits.
  5. Nutty 5.o

    Gt40 (3 Bar) And Gt40 Intake Install Cost?

    I'm near Reading, Pa and think $500 is a very reasonable price. Agree you would be wise to put some money into other items at the same time. I do side work but don't know how close you are. Shoot me a PM if you have questions about reputable shops in the area, etc.
  6. Nutty 5.o

    Finishing Touches On Sc V2 Install

    Sounds like a good set up and very similar to what I had ran years back. What is your exhaust set up? I'm going to shoot high and say 470 but a safe tuned on 93 440-470 is a blast and streetable.
  7. Nutty 5.o

    Found This Car?

    They did back in 03 or so lol! But they were one full piece per side. Haven’t seen what they looked like deftly at Carlisle but I’d check first.
  8. Nutty 5.o

    Where Did You Mount Water Temp Gauge

    NP; just some ideas.
  9. Nutty 5.o

    Brakes Front Brakes???

    Have used this set up twice now with my 89 AOD car driven daily for a few years. It really was a decent stopping car considering with just new parts and the stainless caliper sleeves. Will be a decent until you can install a proper full brake set up.
  10. Nutty 5.o

    Where Did You Mount Water Temp Gauge

    I've put them in two areas: rear factory sensor location and moved factory over to other side and also in the radiator neck. I've usually put the gauge in a center vent 2 gauge pod that retains vents or on pillar. If you have a cowl you could get away with mounting one in that. Personally...
  11. Nutty 5.o

    For Sale Misc. 5.0 Mustang Parts New & Old

    Whoops! Will have front pic coming. $40 for wheel/tire.
  12. Nutty 5.o

    Oops Made 17 Psi And Now White Smoke Come Out The Exhaust?

    Second jrichker's advice. I had all sorts of problems even lesser boost back in the day until I studded the heads. Highly recommend confirming heads/deck/block are all ok and getting studs.
  13. Nutty 5.o

    What Urethane Engine And Trans Mount Do You Guys Recommend?

    Not sure the case these days, but I've had both ES and Prothane. The ES seemed to be a bit smaller for both motor and engine than the Prothane's I put in my 90 months back. Beffier Prothane's were a bit trickier to fit in the engine mounts than ES's were years back but if you're doing a K...
  14. Nutty 5.o

    T-5 Shifter

    Pro 5.0 on foxes have always been my favorite. Have had MGW as well but not on Foxes. They're excellent pieces but I'd want to try one first on fox body.
  15. Nutty 5.o

    Found This Car?

    Agree, that's way too much. And the cobra side skirts are really cheesy as they don't come up to include the GT door trim moldings. At first glance I thought they were the first Cervini versions of the side skirts taht didn't have the separation like the correct/originals at the door openings...
  16. Nutty 5.o

    For Sale Misc. 5.0 Mustang Parts New & Old

    Looking to sell the lot. Various parts I've collected over the years for more recent and older Foxes I've owned. Parts are from mostly 1989 and 1990 but some 1993 parts. New stuff: various underhood and trunk stickers. New repro Cobra intake plaque, ball joints, hood bumpers, hardware for...
  17. Nutty 5.o

    Randomly Shuts Off At Idle

    Yeah, in that case you're probably right.
  18. Nutty 5.o

    Randomly Shuts Off At Idle

    I've had a sensitive igntion switch do this: meaning that the spring back when releasing while cranking over was so strong that it caused the switch to actually go slightly past the "ON" and shut off. Worth testing next time you start that you slowly let it come back. Maybe it's on the edge...
  19. Nutty 5.o

    Anyone Use This Harbor Freight Engine Support Bar?

    I used it on my 05 Focus to replace clutch and it worked fine. Not necessarily the best example for you, but I did use the chains they provided.
  20. Nutty 5.o

    Progress Thread Darkfader's 93 Gt Progress - Back to work

    Nice project and awesome on the garage. You must be beyond stoked?!
Top Bottom
Back
Forums
Menu