Search results

  1. MustangMando

    68 mustang replacing door handles

    Excuse my ignorance, but how do i remove the interior door panel? Thanks in advance
  2. MustangMando

    68 mustang replacing door handles

    Can anyone help me with the replacing of door handle? What is the easiest way to replace door handles?
  3. MustangMando

    What is the right proportioning valve for my 68 stang?

    I have disks in front and drums in rear. Disc/drum mc with booster . Which will my car need and where in the line should it go?
  4. MustangMando

    What is the right proportioning valve for my 68 stang?

    Are residual valves necessary ? If yes do i need one 10 psi or two 8 and 2psi?
  5. MustangMando

    What is the right proportioning valve for my 68 stang?

    What line does the adjustable proportioning valve go?
  6. MustangMando

    What is the right proportioning valve for my 68 stang?

    I just installed a scarebird conversion(front discs), but keeping my rear drums. Is an adjustable proportioning valve necessary, how about residual valves? If they are, what is a good set-up that isn't too expensive. Thanks
  7. MustangMando

    Help locating this hood...........for my 68 stang

    Does anybody know where to find this hood or grille. Thanks in advance, people in this forum are always so helpful.
  8. MustangMando

    How to adjust pushrod? On a 68 stang

    Anybody out there?
  9. MustangMando

    How to adjust pushrod? On a 68 stang

    How do i just remove the master cylinder? The mc is almost hitting the shock tower?
  10. MustangMando

    How to adjust pushrod? On a 68 stang

    Where do i get that tool and where should the pushrod be adjusted to ? Do i need an adjustable proportioning valve or is this optional?
  11. MustangMando

    How to adjust pushrod? On a 68 stang

    Hi guys, just installed a ssbc bendix booster and discbrake/drum brake mc. Vacuum from engine is fine, but as soon as car is turn on the brake pedal gets too soft and wont retract. Turn the car off and brake pedal pulls right out. Called the seller and says the push rod is not adjusted right...
  12. MustangMando

    How to drop my 68 Stang

    Should i cut some of the spring from the passenger?
  13. MustangMando

    How to drop my 68 Stang

    Just did a shelby drop and put in some 620's. The driver's side is 1 inch higher than the passenger. Shelby drop is done correct. The passenger's side is the correct height. Is their something im missing? Shocks aren't in yet.
  14. MustangMando

    How to drop my 68 Stang

    After cutting it a full loop, will the ride be any stiffer? Thanks for the info?
  15. MustangMando

    How to drop my 68 Stang

    I have a 68 Mustang v8(302) with a I6 suspension and i would like to lower it about 2 inches in the front. I would like to cut the springs with a grinder to avoid over heating the springs. Any suggestions? Thanks for any help..
  16. MustangMando

    3speed to t5 on a 68 Mustang

    Do i need an adapter plate for my 3speed bell? What kind of bellhousing plate do i need?
  17. MustangMando

    3speed to t5 on a 68 Mustang

    Most websites say to change out yoke for a shorter one, because it will damage the transmission. Do I cut the old yoke or use it as-is? Thanks, Mando
  18. MustangMando

    3speed to t5 on a 68 Mustang

    Thanks 2+2gt, what bell housing do i use. The t5 came with a foxbody bellhousing. Do i have to cut the driveshaft? Do have to cut the floor? What clutch do you recommend for softer feel? Thanks again
  19. MustangMando

    3speed to t5 on a 68 Mustang

    I need some help, i am swapping my 3speed for a t5. What are the parts that i'm going to need , besides the t5? Can I use the old yoke, and clutch? I'm looking to go with the old linckage or cable clutch . Does the pedal get softer with cable clutch instead of the old linckage? Thanks...
  20. MustangMando

    Left brake light does't work -68 Mustang

    Can i just tie both wires together, the orange and green?
Top Bottom
Back
Forums
Menu