Search results

  1. IMPORTSMOKER

    How are these vacuum numbers?

    11-13 "hg at idle @ 800 rpm and a solid 21" hg at decelleration...this is the result after I put on new intake manifold gaskets...I was only pulling 8-9 "hg....but now im curious if this is where I should be with my setup (all mods in sig...supercharger currently not on car)
  2. IMPORTSMOKER

    just switched from vortech s/c to trickflow h/c/i...what to expect??

    yea i know the typhoon intake will not work...ill problebly use my stocker that i still have and sell the typhoon...
  3. IMPORTSMOKER

    just switched from vortech s/c to trickflow h/c/i...what to expect??

    thanks for the info...btw...my best bet was to sell the vortech for the h/c/i combo....and then pic up a kenne bell (when funds are available).....to take care of the bottom end loss...-----ALSO------this combo will be run with a ported typhoon intake....not the trickflow street intake...**just...
  4. IMPORTSMOKER

    just switched from vortech s/c to trickflow h/c/i...what to expect??

    thats just it.....the boost would build...and even with the 7" crank pulley...i wasn't getting full boost until redline (6000 for me).....i want some low end torque...my car is a fun street car, not a drag car...i like to mash the pedal at 10mph and be thrown in the back seat...with the...
  5. IMPORTSMOKER

    just switched from vortech s/c to trickflow h/c/i...what to expect??

    the vortech is gone.....i was runnig all mods in sig...this new setup will be complemented with a kenne bell s/c in the near future....(taxes....)
  6. IMPORTSMOKER

    just switched from vortech s/c to trickflow h/c/i...what to expect??

    I got rid of the o'll vortech s/c trim...i was pushing 7-8 psi with basicly stock motor...wasn't really impressed....so i just got my trickflow head, cam intake kit from summit...will be installing this week...motor is already torn down and ready for new parts...but what will i see as a...
  7. IMPORTSMOKER

    any cam install tips / help??? installing cam tomarow..

    im installing my trick flow stage 1 cam tomarow...have never installed cam before...but have done timing chain...any other tips on getting the old cam out and new one in without screwing the cam bearings would be nice....thanks
  8. IMPORTSMOKER

    what injectors with h/c/i and twin turbo?

    like i said...i plan on going with 42's in the future...but will i be o.k. for now with just the 30#ers and fmu??
  9. IMPORTSMOKER

    what injectors with h/c/i and twin turbo?

    well i have been running 30# injectors with a vortech fmu and 255 lph fuel pump with my mods in sig......but now im going to a twin turbo setup with about 9 lbs of boost and the trickflow efi h/c/i kit....can i get away with my 30#ers and fmu for a while (until more cash is produced) ...
  10. IMPORTSMOKER

    how lopey is the trickflow stage 1 cam?

    anyone running it??? does it sound noticable over a stock cam??
  11. IMPORTSMOKER

    Anyone running a Typhoon intake / Trickflow H/C combo?

    I think im gonna go with the trickflow engine kit...minus the intake..i will use my typhoon intake...does anyone run this combo? how well will the stage 1 cam and twisted wedge heads work with the typhoon...also this will have a vecco twin turbo on it when i get it all on...
  12. IMPORTSMOKER

    Will an f-cam pass emissions?? compared t an e-cam?

    hey....i haven't recieved that email...maybe try again?? [email protected]
  13. IMPORTSMOKER

    Will an f-cam pass emissions?? compared t an e-cam?

    anyone else??
  14. IMPORTSMOKER

    what kind of power with e-cam and gt-40 heads?

    any other comments??
  15. IMPORTSMOKER

    what kind of power with e-cam and gt-40 heads?

    im thinking of an e-cam...i want heads too but low on cash...would a set of junkyard 95-96 explorer heads (non "p") make decent power compared to stock heads with the e-cam?? is it worth while putting on those heads?? cause the cam is going in gegardless...
  16. IMPORTSMOKER

    Will an f-cam pass emissions?? compared t an e-cam?

    thanks...send it to [email protected]
  17. IMPORTSMOKER

    Will an f-cam pass emissions?? compared t an e-cam?

    I know that the e-cam is emissions legal...but will an f-cam pass as well...with all smog equipment hooked up? reason is hat im looking for a cam that is somewhat emissions legal....that has a nice lopey idle to it and more power..i know the f cam sounds a little better that the e-cam...does...
  18. IMPORTSMOKER

    What size are these??

    those look like 36lbers....ill give you a fresh $20.00 bill.....(not wrinkled..fresh)
  19. IMPORTSMOKER

    E brake light flashes while accelerating????

    had that problem at one time...and yep! its low brake fluid guy...
  20. IMPORTSMOKER

    Front Coil-Overs, which brand???

    I've got the GROUND POUNDERS at all four corners...rear kit envolves no welding (only kit available w/ no welding)....they work great...completely adjustable ride hight....nice ride...pretty cheap in price compared to some other brands....anodized.....no squeeks...pick your spring rate when...
Top Bottom
Back
Forums
Menu