Search results

  1. B

    Cold air fender kit and heavy rain don't mix!

    The filter sits way up inside the fender - right there at the circular cut out in the upper right apron where the stock air plumbing went through - I was thinking the same thing - sheet metal with some screws - but I was wondering if someone has already perfected it.
  2. B

    Cold air fender kit and heavy rain don't mix!

    I have a cold air kit on my 1993 GT that puts the round 7" or so tall high flow filter inside the fender area. I have NEVER had a problem with this set up until today. I was driving for hours in fairly heavy rain and the car started randomly bucking every so often - sometimes worse than others...
  3. B

    5spd gear question after torn down

    great - really appreciate it - going shopping in the morning at Carlisle in the rain it seems......
  4. B

    need help

    I checked my EGR function by putting a vacuum on the tube at idle and when the car ran badly it showed the EGR passages were operational and if the diaphram held the vacuum it was ok - EGR only is supposed to function at warm cruise for better economy.
  5. B

    5spd gear question after torn down

    Oh - does second gear for this trans have 30 teeth? I am going to the show tommorrow and thought I would look for one too - any part numbers for the slider, idler and gear that I should look for?
  6. B

    5spd gear question after torn down

    ok - I will get the slider and the idler for sure - I do not have second gear handy (left the rest of the trans at the shop and they are closed til monday) I see what you mean about the 2nd gear fingers that mesh into the slider -- they mesh into the side of the slider that has the groove -...
  7. B

    5spd gear question after torn down

    Thanks again!! I have purchased the 94 piece ford motorsport t5 rebuild kit 7005a I think it was called and an extra input shaft bearing and race part a-5 at my local auto parts store because the listing for the rebuild kit said I had to buy another one of these for the later model transmission...
  8. B

    5spd gear question after torn down

    Thanks a whole bunch!!! I was going through my service manual book and it looks like this is what it is!!!! I am having a local shop do the work and he thought it was 2nd gear - it is obviously NOT 2nd gear!!! The shop was saying he thinks the fix the part by grinding the rounded over "v" edges...
  9. B

    5spd gear question after torn down

    I have a worn gear and am trying to find out which it is--- Tranny tag reads f0zr-7003-aa rep-av 13-52-199 89369g2413 -- the gear in question was next to the last gear on the tailshaft set of gears -- it has 32 teeth that are NOT angled but have a "v" shape on one edge that has worn...
  10. B

    MSD coil noise

    my Crane FireBall coils BOTH do that on BOTH my Mustangs - I got used to it
  11. B

    cam degree ?'s Advance 2* = ? seat of the pants

    Thanks - however, what's done is done though -- 1.7's and straight up (theoretically of course) -- Just wondering what kind of seat of the pants difference I will feel if I went to all the trouble of degreeing it. As of right now the car runs perfectly, idles at 800rpm with a VERY nice rumble...
  12. B

    5spd input shaft bearing part number for 1993 GT

    nice site - thanks - I think I found it for $11 at Advance Auto parts - part number A-5 - comes w/ race and bearing - looked it up in the book at the store as the computer did not do so well - I also looked it up in my 1993 Mustang Ford service manual - part number 7025 -- I assume you need to...
  13. B

    cam degree ?'s Advance 2* = ? seat of the pants

    Thanks - I am doing a swap soon - Anybody else???
  14. B

    What ALL comes in a FRPP gear set?

    I got an install kit from Summit for about 65.00 - Timken bearings, front and rear pinion bearings and races, carrier bearings, carrier shims, pinion shims, pinion seal, crush sleeve, cover gasket, pinion nut, locktite, ring gear bolts, brush, marking compound, etc....
  15. B

    5spd input shaft bearing part number for 1993 GT

    Anybody know what the part number is for the input bearing and race for the 5spd that is not included in the 94 piece rebuild kit from Ford Motorsport? Or where can it be bought - local auto parts store?
  16. B

    cam degree ?'s Advance 2* = ? seat of the pants

    ttt
  17. B

    What ALL comes in a FRPP gear set?

    nut, crush sleeve, set of spacers, ring, pinion, that is all...
  18. B

    cam degree ?'s Advance 2* = ? seat of the pants

    Still wondering if it will make a NOTICABLE (25hp or 5hp & torque etc...) difference per a given RPM down low per each 2* advance degreed into the E303 cam or if I should skip this major undertaking and look for other ways to improve off idle seat of the pants pull. What kind of RPM low end...
  19. B

    fuel pressure question

    Check all your fuel lines for crushing or kinks that may happen if the car got jacked up in the wrong place or something like that - if they all look good I would get a Kirban AFPR for $60 or so from CJ Pony Parts - sounds like that is your problem and this is a nice piece for cheap price -...
  20. B

    cam degree ?'s Advance 2* = ? seat of the pants

    I have searched - My E303 w/ 1.7's feels wimpy off idle but comes on strong after several hundred RPM's - I miss the low end pull of the stock cam w/ 1.7's right off idle. I read advancing the E303 cam by as much as 6* will increase low end punch off idle --- BUT how much? What can I expect to...
Top Bottom
Back
Forums
Menu