Search results

  1. J

    8.8 rear end rebuild

    my trac lock unit is shot...i got the one wheel blues my question is should i just get new clutches for the track lok unit or should i do all the bearings and all that good stuff. also if theres a part number/where to get a good heavy duty rebuild kit let me know...im also going to put some...
  2. J

    Question about 2nd gear.

    i would buy the ford racing super duty T-5 from summit...thats what im gonna do when mine goes
  3. J

    cam question

    the only thing dont have is different heads...off road x pipe, 2 chamber flows, and gears are on the way..also got cobra intake..what do you think? still stay away from B or E cam
  4. J

    synthetic vs. mineral oil

    mobil 1 at sams club 23 bucks for a 6 pack
  5. J

    cam question

    speed density cam question i have an 88 LX 5.0 5 speed speed density, has any one have any problems running a B or E cam...such as idle problems or anything? i read in summit racing it says to use mass air, in the 5.0 resto magazine it says 5 speed recomended and gear change. thanks
  6. J

    Throttle Body Coolant Bypass?

    i wonder what they did on the 93 cobras? did they use 1 hose or block it off coming out of the lower intake and block it from the heater core pipes that run along the passenger side of the intake
  7. J

    Is this a blown headgasket?

    i had the same situation when i put my intake on and i put the gasket on the housing then the thermostat and it was burning antifreeze and leaking like a sive out the t-stat housing
  8. J

    cobra intake spacer

    thanks for the info
  9. J

    Throttle Body Coolant Bypass?

    i would just use 1 piece of hose so you dont have to worry about it blowing off
  10. J

    wtf was that?? (help!!!)

    happen to me before, the floor mat got wedged between the pedal and it was at WOT
  11. J

    Throttle Body Coolant Bypass?

    i bypassed mine because the cobra intake doesnt have it, i just used one piece of coolant hose, you can probably also just use a cross threw for the 2 hoses
  12. J

    pulley question

    any suggestions on how to get the alt pulley off without an impact?
  13. J

    cobra intake spacer

    its possible, doesnt really matternow, runs fine with the spacer
  14. J

    cobra intake spacer

    when i installed my upper and lower intake with out the spacer and i started it up and it went to 6k rpm and when i put the spacer on it idles normal, any ideas why, im gonna run the spacer regardless just wondering what this happened
  15. J

    Intake vac. question.

    i belive one goes to the map sensor
  16. J

    pulley question

    i have an 88 LX 5.0 and im going to put on a set of march under drive pulleys i got for free and do i need a pulley puller to take the stock crank pulley off?
  17. J

    Best water pump ?

    i have a question about water pumps, on the police interceptor issued mustangs used for highway patrol they use a heavy duty fan clutch, do they also use a different water pump, or is it the same that is on any 5.0
  18. J

    intake bolt

    thanks alot, i just ordered them up
  19. J

    intake bolt

    does any one have a 7 inch 5/16 thread bolt for a cobra intake, i need one, checked hope depot,autozone,local hardware store, and local automotive stores no luck....any one have any idea where i can get one
  20. J

    Cobra Intake Install on my 87 5.0

    i just recently did the upper/lower on my 88, i replaced the air tempeture sensor and th coolant tempeture sensor, as far as the coolant lines to the TB, i just took the old ones off and put a bigger hose connecting the two of them, you can probably get away with a cross through thing, i also...
Top Bottom
Back
Forums
Menu