Search results

  1. apats77

    My 98 GT

    thank you, i had completely forgot about it
  2. apats77

    My 98 GT

    Upon further investigation the differential was toast. American Muscle coming up with another shipment FRPP 3.73s $139.99 FRPP LOK Limited Slip Diff $179.99 FRPP Ring and Pinion Install kit $99.99 Racking up the parts this week.
  3. apats77

    My 98 GT

    it started with buying the car $2200 w/ 131k Miles Purchased : Fram Air Filter – $14.99 (VIP) Fram TG Oil Filter - $6.99 (VIP) (8) Autolite Platinum SP - $22.00 (VIP) Motor – $500.00 (CL) FRPP PI Intake – $159.99 (AM.com) Install kit- Heater tube, O-Rings, PI Gaskets, Water pump O-ring, Thermo...
  4. apats77

    SVE Mongoose Clutch

    its stock cable and quad. it is adjusted to its max already, cable is stretched out? it starts to grab at about half way.
  5. apats77

    SVE Mongoose Clutch

    Installed the mongoose and a new Ford Racing Nodular flywheel, from stop the clutch slips quite a bit and almost every time in reverse. It slips enough that I can smell it. After about 10 minutes of stop and go the clutch grabs fine. Is this just part of the wearing in period?
  6. apats77

    Ford Evos concept foretelling of 2015 Mustang?

    first thing i thought, looks just like the head of a Cobra with its mouth open
  7. apats77

    Mountaineer 4.6L

    the motor was pulled because it had a "bad rapping sound". Thats all i know about the motor, yes it is an alum block. I just finished doing an engine swap (npi to npi) I dont have the time or shop anymore to do another swap. :notnice:
  8. apats77

    Mountaineer 4.6L

    I have an 04 Mountaineer motor. Since its a PI motor, are the Heads and Cams compatible with my 97/98 NPI motor?
  9. apats77

    After action report

    Wish i could afford a couple of mufflers. IMO it sounds great up past 4k but severely lacking from idle up to. An recommendations for a best bang for the buck? The lower sounding the better as long as it dont drone I do a lot of highway.
  10. apats77

    Dorman Intake, OE oil cooler

    Reduced $120 Shipped or BO
  11. apats77

    Dorman Intake, OE oil cooler

    I have a Dorman NPI Intake with Alum x-over, also the OE oil cooler off my 98 GT. The cooler came as an option with the Sport package. If needed i can include torque sequence for intake. (You will need gaskets for both) Asking $150 shipped or BO please PM
  12. apats77

    After action report

    So we completed the engine pull and install. Bought the 97 engine on craigslist. It had been sitting for almost 6 months, after a final check and a few seconds of cranking, without coils plugged in, to build oil pressure it fired right up. 98 mustang GT - YouTube Now I just need to do...
  13. apats77

    Engine problems and shifting issue

    change fuel filter and run some injector cleaner.
  14. apats77

    What should i do with my mustang

    ever given it a tune up? Id start with Air/fuel filter. then atleast plugs. Also how hard do you drive it is the real question?
  15. apats77

    Lower radiator hose

    On my 1998 the motor had an oil cooler well the new motor is a 97 and does not. I need to complete the build today and I can not get the gasket to switch the cooler to the new motor. So the lower hose that was on the 98 cooler doesnt seem to fit on the 97. Is there a different hose that i...
  16. apats77

    Engine removal

    SiahNyde : Its a 1998 GT 5 Speed Lugnuts: Thank you for the input. We are dropping the trans as well. Unfortunately I have no money left after buying all the parts to buy a tubular K member. Any other tips or tricks or warnings you can give me is much appreciated.
  17. apats77

    blown motor part out

    make an offer
  18. apats77

    Engine removal

    Taking the junk engine out on friday. We decided going through the bottom would be better. Any one have a break down on how this is done? We have a full shop at our disposal
  19. apats77

    FS: 2002 4.6 PI Engine

    thats a great deal :eek: