Search results

  1. 6

    double pumper tuning with sbf

    I measured it (with a dial caliper and wooden stick) TC is off by some 6 degrees, new balancer is on the way.
  2. 6

    double pumper tuning with sbf

    I am looking for ford racing M 6316 K351 or similar balancer to replace the original one on 1973 302 windsor, jegs carry it for some 60 bucks but they offer expensive shipping methods. I am in Europe. Engine does not start, once heard a bad metal detonation (not sure if at 6 or 12 btc).
  3. 6

    double pumper tuning with sbf

    Right, still could not start it although carb does not flood the engine any more, AC shoots fuel, and 4-4.5 psi pressure builds at the needle, fuel level is stable. MSD gives spark to 1st cyl. so I assume it gives to all cylinders or shouldn't I? So played with timing. Started at BTC 12, went up...
  4. 6

    double pumper tuning with sbf

    Marginal I meant the point that the engine starts to disbenefit from any higher cfm. i.e. carb provides more mixture than engine can suck. IMO this is around 550 cfm for this engine. Why is even 600 too much? E.g. Holley recommends 390 cfm, I know they are more on conservative side. If you have...
  5. 6

    double pumper tuning with sbf

    I tried everything (advance timing, leaner mixture), nothing worked, and decided to take carb apart and figure out the problem by myself. It turned out that new needle that I replaced as a part of rebuilding this carb (was part of holley universal kit for 4150s) had slightly different oring. The...
  6. 6

    double pumper tuning with sbf

    I have 600 cfm DP (model no.4777) on a mild cam 302 engine, Weiand dual plane manifold, MSD 6T ignition and duraspark II distributor. I am having a problem to properly tune the carb. I can start the engine only with rich settings and choke making huge amount of white smoke filling garage for 2...
  7. 6

    Type-F ATF Equivalent or Replacement???

    You must have Valvoline out there, they are all over the world, they carry type F fluid
  8. 6

    Will 18x8 rims fit in the front on 1964 1/2 ford mustang

    IMO 18 rims with low profile tires fit better than 17 rims with mid-profile tires. This is because 18 rims will clear upper A arm at a higher distance than 17s, thus rims may have slightly higher backspacing and lesser chance that fender is hit when passing through a bump. But this is for 67-68...
  9. 6

    cowl vent

    definitely weld the driver side, keep passenger side
  10. 6

    cardboard tube inside driveshaft

    anybody knows what this cardboard is supposed to do inside the driveshaft? it is 67 v8
  11. 6

    motor mounts fitment issue

    yeah just did it. fortunatelly whoever did this those welds were one of the crapiest I have ever seen on a car and one day the engine would fall.
  12. 6

    motor mounts fitment issue

    Just realizing how I overlooked this part of v8 swap. Thanks DC for help this would be another $100 (assuming you would ship it over Atlantic) I just bought dash pad for $150, and have 8" rear leaking & your stores will cash me $50 for a pinion seal and going to starve until the next paycheck. I...
  13. 6

    motor mounts fitment issue

    I bought motor mounts for 67 v8 289 in advance auto and i have problem to align the '73 302 engine with them in 67 mustang. The engine is shifted about 3/4"to the driver side, and twisted too, counterclocKwise, about 3/8" (measure at valve cover and inner fender). Trying to figure out what...
  14. 6

    Battery in the trunk, need cable routing ideas.

    Place it behind quarter panel (passenger side), then route it under the trim (same as stock wiring on driver side), kick panel, then route it inside the engine bay. Or inside the fender and enter the engine bay from right under the solenoid
  15. 6

    Timing light and MSD ignition

    Wires? I am using autolite # 96205, the other car that this timing light works with is carbed 4 cyl. and uses some noname thin wires. MSD tech said not all timing lights work with their ignitions, especially those with advance button. Has anyone seen this light working with MSD?
  16. 6

    Timing light and MSD ignition

    I have MSD 6T box. My timing light - http://www.muscularmustangs.com/tools5.jpg (old sears/craftsman with advance dial) fails to work. It works with regular point single spark distributor. Is there anything that can be done to the timing light to make it working?
  17. 6

    Cobra brakes

    you will need new rear axle bearings too because the bracket will not slide through + machine a little gap around to seat the bearing into the bracket. Also what rear rotors are you going to use?
  18. 6

    Where can i get a complete granada break system...

    I got 4 wheels disc power brakes for far less than the kit costs for the front w/o booster. Four crossdrilled rotors, front and rear loaded calipers and spare rotors, four brake hoses, emergency brake cables, MC and booster off junkyard, custom brackets for OE spindles, summit proportioning...
  19. 6

    Clutch Cable

    v8-nice work, I tried with more unappropriate headers. OE cable is about 3-4 in. shorter than yours and I see yours fits just right.
  20. 6

    mustang stores COUPONS

    We buy parts not only during Xmas but throughout the year and guess what who does not want a better price? If you know about a x%-OFF coupon or a sale event will you post it here?
Top Bottom
Back
Forums
Menu