Search results

  1. K

    Replacing flywheel ring gear?

    My dad and I installed one of these on a junker Ford Ranger I used to drive when I was 14. We either got the wrong gear or it wasnt installed flat. As the Ranger kept eating starter gears for the next few years till we had some major engine problems that were not cost effective to repair...
  2. K

    9" Axle bearing install 101, Q?s

    This axle is set up for disc and I used a slide hammer I rented from my local auto store for free to pull the axles. I do plan to have the bearings removed and pressed by a local shop, I'm just waiting for the new bearings in the mail, thanks for your feedback!
  3. K

    9" Axle bearing install 101, Q?s

    Yea, I'm using the stock Versailles brakes. I called a Hydraulic House that I found online who is located in FL and the said the do not work on any lines that run brake fluid? Where is the Co. you used located. I got a deal on the axle bearing kits from Auto parts warehouse about $76.00...
  4. K

    9" Axle bearing install 101, Q?s

    Thanks to all of you for your help! I just test fix my stock brake system on my Versailles 9" rear. I went w/ the stock brakes and so far only have about $180 in my brakes, but still need hoses, oh well. My questions are: From what I have read from some of the links members have...
  5. K

    Which Master Cyclinder & Proportioning Valve

    I forgot to ask this question and no one has mentioned it? Since I have a single bowl MC, which distribution block should I get? I prefer to by a cheap factory block or pull one from a yard vs. paying $$ for a custom brand block. I plan to order the SSBC Brake Proportioning Valve after...
  6. K

    Which Master Cyclinder & Proportioning Valve

    This what I will install this weekend, any tips on the petal linkage or is it a direct bolt in? I will be asking you a lot of questions over the next few moths as we will have a very similar set up, thanks!!!
  7. K

    77 Versailles rear install tips?

    I'm looking to do your exact same stance and wheel/tire combo, looks good!
  8. K

    77 Versailles rear install tips?

    The brakes on mine are shot, the lines are even bent and damaged w/ no e-brake cables. I'm thinking about using different brakes, something a little more available. Kinda thought about the Explorer set up, I'm looking to save money here, so mustang Steve might be a little too high (still need...
  9. K

    77 Versailles rear install tips?

    I just purchased a 77 Versailles rear 9" for my 65 coupe. I plan to have cleaned up, refreshed and installed in next month or so. Please give me any advise or tips you may have on the install, rebuild or brakes. I have read all the articles on the rear end swap sticky. Please give me any...
  10. K

    Which Master Cyclinder & Proportioning Valve

    Ok I just made a deal w/ a guy w/ a 77 Versailles rear (as long as it goes through), so the the lincoln brakes will be my rear.
  11. K

    Which Master Cyclinder & Proportioning Valve

    Which Master Cylinder should I use running disk front and rear. I just installed 10 1/4" front discs (Scarebird kit) and am still trying to decide on the rear. Will it be an issue if I change to the new dual bowl master cylinder 1st and prior to changing the rear from drum to disc? I...
  12. K

    Rotor size for Scarebird front disc?

    I found it about 10.25". Please feel free to post any comments on this set up.
  13. K

    Rotor size for Scarebird front disc?

    I'm thinking I like this kit, any one know the rotor size and have a complete parts list (more than whats listed on the web site). Scarebird Classic Brakes LLC Also anyone have any issues later installing power to this set up?
  14. K

    Chrome or Polished Bullitt 17's???

    Whats your wheel & tire / supension setup, thats what I'm lookin for (on a buget).
  15. K

    Chrome or Polished Bullitt 17's???

    I'm not interested in the wheels w/ the gray painted spokes or I would buy some used take offs, thanks for your responce.
  16. K

    Chrome or Polished Bullitt 17's???

    I’m thinking about buying either chrome or polished aluminum bullet wheels for my 100% stock suspension 65 coupe w/289. I thinking about saving $100 bucks and buying the polished aluminum? This is the brand I'm thinking about buying...
  17. K

    going to attemp to redo my seats

    I did my front seats on my 65 this weekend. I agree w/ letting them lay in the sun. I also put burlap between the seat and the frames. I had problems getting the hog rings to attach to the inner section to the frame (listing rod?) so I took some extra clothes hanger wire and made 1" U shaped...
  18. K

    GM TBI or Holley Projection

    Yea, your write up is what got me thinking of TBI EFI, I’m just a little intimidated by the Mega Squirt and don’t wanna have the car setting for months while if learn MS, that's why I'm looking for an easy route. I would like to go MS but will need to do much more research.
  19. K

    GM TBI or Holley Projection

    I'm kinda thinking about swapping in a 351 in my 65, 289 coupe. Any thoughts of GM TBI or the Holley projection. I wanna go w/ fuel injection, but keep a stock look and hide everything under the air cleaner. Link for GM TBI swap: GM TBI Swap
  20. K

    Help me plan my build!!!!

    Measured the Tbird T5 shaft (rough measurement): about 7 1/2" from outside of transcase to tip of shaft and using a straight edge on the rear of the stock bellhousing 7" from straight edge to inside of bellhousing.
Top Bottom
Back
Forums
Menu