Search results

  1. 91five-o

    Boost Guage

    :bang: Alright............call me stupid if you want but I just can't seem to get the guage to work. I blew into the tube to see if the needle would move and it did so I know the needle isn't stuck. I plumbed into my vacuum line to the FMU and the guage didn't work either. I have tried a...
  2. 91five-o

    Boost Guage

    Can someone please tell me where exactly they have installed their guages I tried it never worked. Thanks Ian
  3. 91five-o

    Need FMU ?

    Got the car started.......had to step on the accellerator pedal while it was cranking over before it would fire. Idle was way too low so we turned it up some to allow it to keep idling. Timing was put back to 10 degrees. I was running a C&L 73mm MAF meter and have upgraded it to an 80mm C&L...
  4. 91five-o

    Need FMU ?

    Just finished the install of an S-Trim. Car fired right up and I let it idle for a few minutes as directed. Turned it off as I had to get ready to set the timing back to stock. Car will now just turn over and not fire. Checked for spark - OK, so I'm now wondering if the car flooded. I am...
  5. 91five-o

    Accessory Belt Too Short

    Simple solution.............went down to my local auto parts store and bought a longer belt. No sense wondering why the stocker woudn't fit, the new one works great ! :nice:
  6. 91five-o

    Boost Guage Install

    Just wondering what vaccum line I splice into to install my autometer boost guage will anyone work or does it have to be a specific one. Also just curious how this guage actually tells you your boost if it is plumbed into a vaccum line.
  7. 91five-o

    Which Sparkplugs ?

    Just finishing up my S-Trim install. Currently running autolite 24's for plugs. Will these plugs work O.K. and what should they be gapped to. If I need something different, what should I use and what should they be gapped at. Ian
  8. 91five-o

    Accessory Belt Too Short

    Installing a vortech s trim has anyone run into the stock accesory belt being too short. It says to use the factory belt but mine is about 1 1/2 to 2" short. Have I done somthing wrong? I have followed the instructions carefully.
  9. 91five-o

    Flexlite Fan Spacers

    Just wondering if it is ok to double up these spacers as they only go up to 2" and with my new vorstech s trim crank pulley the belt will not clear the fan with my 2" spacer? Any suggestions or has anybody encountered this with theres'
  10. 91five-o

    Snapping/Cracking sound in Rear

    For a long time I have had this snapping sound occuring from take off in reverse or forward and when downshifting. It only occurs underload it seems. Lately this sound has been happening very often pretty much doing it off every standstill. I have checked all me bolts and bushings to make sure...
  11. 91five-o

    Oil Pressure

    What PSI are you guys runnin for oil pressure?
  12. 91five-o

    Calibration Tube for Mass Air

    Hi I purchase 42lb/hr injectors and I have a C&L 73mm mass airl flow meter. When looking at sampling tubes I noticed for 87-93 mustangs the green tube is the biggest made and it says for 38lb/hr injectors, but on a 93 cobra the same size mass air everything, green tube is for 42lb inj. so will...
  13. 91five-o

    Fuel Pressure with Supercharger

    Just wondering what I should set my fuel pressure at with my supercharger. I have a powerdyne 9 psi kit and aslo have 42lb injectors. Any suggestions?
  14. 91five-o

    Buying a Supercharger

    I am in the process of buying a supercharger most likely a vortech s trim. I have the following mods done already and I was just wondering what else I should have. I know I need bigger injectors but should I get 42lb or 36lb and also would my mass air and throttle body be adequate? Thanks in advance
  15. 91five-o

    Installing A/F Ratio Guage

    Have an autometer a/f gauge just wondering what wire on my o2 sensors is my signal wire or the one I have to splice into? Thanks
  16. 91five-o

    Coolant Temp Sensor

    Can anyone tell me where the coolant temp sensor is located. I think it is the thing in the hard line that goes to my heater core but can someone tell me for sure. Thanks
  17. 91five-o

    Power Steering Pump Pulley

    Thanks for the help.................Happy New Year ! :D Rick
  18. 91five-o

    Power Steering Pump Pulley

    I have borrowed a puller however what I was wondering about is the "four sided collar" which is in the middle of the pulley. Does this have to be unscrewed or removed first or just use the puller and all will be fine. I'm new to this.............sorry ! Rick
  19. 91five-o

    Power Steering Pump Pulley

    :( Need help getting the pulley off the power steering pump. Anybody ? Rick
  20. 91five-o

    MSD 6AL vibration mounts

    Are the vibration mounts that are supplied with the ignition box really crucial to be installed or am I able to just leave them out? Thanks
Top Bottom
Back
Forums
Menu